Jump to content
SAU Community

Recommended Posts

I just put a walbro gss341 fuel pump in my car. The car started using stacks of fuel. I pulled 30!!! units of fuel from the power fc and it ran better. No extra knock. Still reads rich on acceleration on the narrow band. Sounds to me like a worn fuel reg. Any ideas?

Link to comment
https://www.sau.com.au/forums/topic/366222-fuelideas/
Share on other sites

I had the injectors at 85 percent before and now they are at 75 percent. The idea that the previous fuel pump was lazy is good. It would explain random knocks on wot after holding it flat for a while. I'll do some more tuning and test some bits and see where it ends up.

Link to comment
https://www.sau.com.au/forums/topic/366222-fuelideas/#findComment-5842556
Share on other sites

Not utterly useless but fairly useless. Obviously you arent going to run full load at stoich. Like I said it will let you know if rich or lean which generally is only usefull initially. After that its a bit like tuning a carby lol. Add more fuel till it loses power. :whistling: There are stacks of variables to know when tuning a engine which I wont go into now. My point regarding the narrowband in this thread is that even after I pulled 30 of the entire inj map it still didn't run technically lean. You blokes know what I'm on about by now. That is heaps of fuel to take out. Shitloads in fact. It is definitely too lean now to give a hiding to for extended periods but it will get me to work till the datalogit and wideband arrive later this week or early next week.Try $30 a day for fuel and only doing about 40 or 50 k's. Ouch :glare:

Edited by Room42
Link to comment
https://www.sau.com.au/forums/topic/366222-fuelideas/#findComment-5843370
Share on other sites

you cant use the narrowband to determine how rich its running under accleration.... it could be lean for all you know

:stupid: Read up on what rich and lean means mate. 14.7 is the middle, a lower number is rich and a higher number is lean. I did mention in the first post the gauge read rich lol.

Link to comment
https://www.sau.com.au/forums/topic/366222-fuelideas/#findComment-5843389
Share on other sites

i know how it works.... i meant too lean for the conditions, acceleration calls for a richer mixture than 14.7:1 (a narrowband simply tells you which side of 14.7 your on), so yer it might be on the rich side of 14.7 but still too lean for the conditions.

Link to comment
https://www.sau.com.au/forums/topic/366222-fuelideas/#findComment-5843412
Share on other sites

i know how it works.... i meant too lean for the conditions, acceleration calls for a richer mixture than 14.7:1 (a narrowband simply tells you which side of 14.7 your on), so yer it might be on the rich side of 14.7 but still too lean for the conditions.

eg. You could be at 13:1 when it should be at 11:1, narrowband would simply tell you you're rich even though it's still too lean.

I follow you Jonno, I follow :D

Link to comment
https://www.sau.com.au/forums/topic/366222-fuelideas/#findComment-5843486
Share on other sites

i know how it works.... i meant too lean for the conditions, acceleration calls for a richer mixture than 14.7:1 (a narrowband simply tells you which side of 14.7 your on), so yer it might be on the rich side of 14.7 but still too lean for the conditions.

Agreed. Its on the safe side for getting me to work but not for flogging the crap out of it. Odd that so much fuel came off the map tho.

Link to comment
https://www.sau.com.au/forums/topic/366222-fuelideas/#findComment-5843644
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...