Jump to content
SAU Community

Recommended Posts

Car - 180sx

Engine bay:

Engine - RB25

RB25 Gear box

Garrett GT3582R .82ar

turbo has been hpc coated

6Boost manifold

Link G4 ECU

GFB 50mm Gate to screamer pipe

Greddy plenum

custom billet fuel rail

1000cc injector dynamics injectors

2x walbro intank fuel pumps - adding surge tank and Bosch 044 pump

turbo smart blow off valve

custom dump pipe

600x300x100 fmic

JJR 19row oil cooler

oil catch can

HI TORQUE solid centre heavy duty clutch

alloy radiator

2x thermo fans (work by the ECU)

powersteering spacer for more lock

superspark coil packs

hi-cas powersteering pump

Q45 throttle body

Engine Work:

full valve service

crack tested head

bleed and clean hydraulic lifters

chemical clean and acid dip block

deck block

TOMEI head gasket

head reconditioned

bottom end machined

ARP head studs

HI ENERGY pro eliminator sump (HUGE)

nismo oil pump

CP piston kit 20 thou

CP Piston rings

ARP main studs

main bearings

rod bearings

GATES racing timing belt + full timing kit

Incar:

autometer cobalt monster tacho

boost gauge

oil temp

oil pressure

custom brake lines for hydrolic handbrake

Velo seat - still need to get rails for so have a s15 seat ATM

s15 passenger seat

full roll cage with padding

hyrdo handbrake and normal handbrake aswell

carpet is gone

full race harness

battery relocated in rear

Outside:

180sx Full Works body kit

5 stud conversion

32gtr front brake upgrade

clear tail lights

rattlecan matt black paint job

white 18inch wheels

custom 3" exhaust with twin 3" outlets

racing logic coilovers

all the bells and whistles in suspension including strut braces,tie rod ends etc

2.jpg

4.jpg

7.jpg

9.jpg

15.jpg

Link to comment
https://www.sau.com.au/forums/topic/366503-damits-180sx/
Share on other sites

  • 2 weeks later...
  • 1 month later...
  • 4 weeks later...

I'm building an rb25 gt35 silvia atm, So jelly you have had yours on the track pinch.gif

Have you weighed it?

Apparently due to the large rear windscreen 180's are heavier than silvias... I would be interesting to see how much it weighs

Link to comment
https://www.sau.com.au/forums/topic/366503-damits-180sx/#findComment-6000405
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...