Jump to content
SAU Community

Recommended Posts

Hey guys, so my 32gtr is still giving me grief and I have absolutely no idea how to begin the trouble shooting process. I have the complete service manual and basic tools.

I am wondering If there is a gtr savvy member living around the maylands area who is interested in spending a few minutes answering questions and having a look at my car(try and get it going properly) for the price of a carton of their choice. I have read through hundreds of threads on this and other gtr sites(Canada gtr is also very good) but have not managed anything solid.

Cheers in advance guys. Here's hoping. :)

Jesse.

Link to comment
https://www.sau.com.au/forums/topic/366889-anyone-keen-to-help-for-a-cost/
Share on other sites

  • Replies 180
  • Created
  • Last Reply

Top Posters In This Topic

Well it's very similar to the problem benno2 was having, started her up and let it idle for a few minutes to warm. Cruised slowly around the block(probly 1k) then, going up a slight hill the revs started dropping even though I was still accelerating. They progressively dropped all the way down and the was almost stalling on a rough idle. Totally confused I killed the ignition not wanting to do more damage. About 4 hours later I tried starting it and it started with a regular idle but a bit low and drove back here with

What felt like slight power loss.

What do u guys think? Mass air flow? Hopefully not gasket? Is this a turbo fault?

I'm moving from a 96 v8 fairmont so this is allllll new to me.

Thanks all.

By the way I'm located right by maylands traino.

Jesse.

Ok, so I just pulled my top Afm out to have a looksi.. Previous master has obviously already resoldered our connections here. This is the joins, sorry they're upside down.. :P

cfc0a840.jpg

dfb4f2d2.jpg

And this is what I assume is the O2 sensor.

07642c77.jpg

3e35baf2.jpg

Very oily/dirty.

What do we think guys?

Thanks for the input. And Boss-Zilla, this is pretty much all I've done so far.

Jesse.

thats the hotwire of your AFM and its filthly lol that will probly be your problem (o2 sensor is in you dump pipes after the turbo), spay it with some electrical contact cleaner, DO NOT touch it with anything, next thing is to figure out where that oil came from.

Edited by horrace

That is the hot wire (sensing) element in the airflow meter, O2 sensor is in the turbo dump pipe.

And that looks like a shitload of oil on the afm, look up the cleaning DIY and see how it goes.

Got a catch can?

Edit: beat me to it horrace!

Just need to clarify, really I meant an oil/air separator.. contains baffles etc and is used to scrub oil from the air before returning it to the intake stream. Always a good thing on a boosted, legal, recirculating breather setup.

A catch can just catches any oil that may come out the breather and is a safety measure required in some racing, usually used in atmo breathing setups (and in recirc setups by people who bought cheap catch cans off ebay).

Jesse, to me it sounds like a vaccum leak and another possibility is intake manifold gasket leaking.

Have a look in the workshop manual for the vaccum layout, will show you all the hoses - make sure they are all good.

To search for leaks in intercooler piping and manifolds, grab a can of Aerostart or similar and with the engine running, spray around all the joints in the cooler piping and intake manifold - if the revs pick up you've found your leak.

Oh dear, most of the vacuum hoses look like this; (these are top and bottom turbo control solenoid hoses respectively)

9126f7f9.jpg

b0c17282.jpg

I'm about to go get some aerostart to test em but I think they will all need help soon. At least if I can get it driving ok I can get it to a mech.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...