Jump to content
SAU Community

Recommended Posts

1993 Nissan Skyline GTS-t.

Had a prang in April - someone made a turn in front of me. Insurance (JCI) said that the salvage is worth $2k according to some auction place (can't remember the name, i've got it written down somewhere, will advise later) so i guess I'm looking for around that price although i am open to offers.

First and only Australian owner - purchased in 2001.

Hasn't seen much driving in the last 3 years.

Windows are tinted to darkest legal tint - driver's side window has some scratches in the tint but the rest is good.

Serviced every 5000-8000kms. Have all service receipts since purchase.

Polyurethane bushings

Reconditioned turbo replaced when the factory ceramic turbo died - "good for 400hp" said the mechanic at the time - dunno what brand it is, but it's larger than the standard - i've only ever run the stock boost, so never got to experience the extra power... oh well...

Rims are the standard ones, but have been chromed or something by the previous owner to make them shiny and look quite nice when they're clean - i cleaned one up a bit so you can see.

Tyres are BF Goodrich 225/50 ZR 16s and have heaps of tread as i haven't done many kms on them and i'm too old to do burnouts.

Splitfire coils that haven't seen much travel at all (probably 1000 - 2000kms if that? I suppose i can check my receipts and figure it out) which i've taken out and put the standard coils back in (one of the standard coils is dodgy). I'll sell these separately.

JVC head unit. bit worse for wear and the "forward" button doesn't work, but the unit still plays CDs/MP3s and radio.

JBL 2 way 4"x6" front speakers

Kicker 3 way 7"x10" rear speakers - you don't need a subwoofer with these installed. Well, at least i didn't...

3" exhaust from the cat with 3" straight through muffler

pod filter

AFM used to be dodgy, but since been fixed - just needed to resolder a connection on it and hasn't given me a problem since i fixed it a couple of years back. (FYI, advice to anyone who has a dodgy AFM and has nasty stalling issues like i did - just unscrew and pull out the plug, re solder it and it'll be like it never happened!)

Also have a Consult Port->RS232 adapter, which helped my diagnose my AFM issue.

apart from the obvious, the passenger door and rear quarter panel is scratched/dinted, the rear bumper also has a couple of scratches/dints but most of the rest of the car is fine. I can take more photos on request.

Location is in Point Cook, Victoria.

Pics are available here - http://franksemails.com/skyline-wreck/

If you want a pic of something specific, let me know and i'll put it up.

Link to comment
https://www.sau.com.au/forums/topic/367340-r32-gts-t-wreck-for-sale/
Share on other sites

  • Replies 93
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Looking to sell the car as a whole at this point.

After 7:30-8ish on weekdays is a good time to take a look. Weekends are ok too most times depending on what i've got on. PM me if you want to arrange to take a look at it.

Edited by verger

Had a query regarding fixing the AFM. Just thought i'd post details here so everyone knows. The problem that i had was that the socket's solder had broken, so they needed to be resoldered. Been a few years since i did this so my memory may be a bit scratchy :)

In the pic you can see my AFM. (1) Remove the plug from the socket, and then (2) remove the 4 screws - once you've done that you can lift the socket and it should reveal 4 or 5 long metal wires which are attached to some other part inside. The solder on my unit was quite brittle and broke off quite easily. I think i also had to remove the plate to have easy access (3 and 4) to where the wires were supposed to be soldered to (or maybe i didn't have to remove the socket at all and could get to it all from under the plate - can't recall exactly). All you need to do is resolder those wires back where they were soldered and you're done.

post-49595-0-71398600-1309752596_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...