Jump to content
SAU Community

Recommended Posts

firstly i would say check ALL OVER THE CAR for a pink / green / purple plate etc etc.. check in the door jambs on the passenger door..

if it's still not there i would be inclined to say that no, you will definitely not be able to get that vehicle complied with an RB26. or possibly comply it at all...

that said - i see you're from queensland - and from what i see over there, it's pretty much anything goes if you slip em a XXXX!!!! ahahaha

firstly i would say check ALL OVER THE CAR for a pink / green / purple plate etc etc.. check in the door jambs on the passenger door..

if it's still not there i would be inclined to say that no, you will definitely not be able to get that vehicle complied with an RB26. or possibly comply it at all...

that said - i see you're from queensland - and from what i see over there, it's pretty much anything goes if you slip em a XXXX!!!! ahahaha

LOL yer wish it was that easy

i looked every were its like some one half tried to comply it cos its got the side intrusion bars but just no paper work and no green plate

no wonder it was cheap

are you brissy based? if so I can probably help in a way.

whn you bough it was it registered at all or had it been through registration?

do you have a chassis number at all?

are you brissy based? if so I can probably help in a way.

whn you bough it was it registered at all or had it been through registration?

do you have a chassis number at all?

i'm in central qld

it hasn't been registered no aus vin number just the jap one

ok ,

when you bough it did you get ANY of the import paperwork with it?

if so contact a RAW that can comply your type of car and tell them the story. www.raws.com.au will give you a starting point.

if NOT then you have a track pig only. it cannot be registered here.

My car is currently registered, but the compliance plate has been lost from a re-spray and re-build. now the previous owner is being a C&*T and doesnt want to help me in any way. I dont have any import papers, just the new aussie vin has been stamped on the drivers strut tower. Is there anything you can suggest Chris for me to get a replacement so I can get a roadworthy?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
×
×
  • Create New...