Jump to content
SAU Community

Recommended Posts

hyper gear tr43i turbo externally gated t3 flange and v band rear housing held 370rwhp on my r33 easy- $450

1x r33 intake manifold bare just top and bottom -$50

1x r33 intake manifold complete with injectors rail and sensors-$100

2x r33 throttle bodies one with tps other non and one s1 and one s2-$40 each

1xr33 pink label afm-$60

2x 12"(i think) thermo fans- $20

1x r33 exhaust manifold-$50

1r33 man ecu -$60

1x r33 standard air box-$30

location Brisbane

contact on here or 0412383721

Link to comment
https://www.sau.com.au/forums/topic/367418-cheap-r33-parts/
Share on other sites

whats needed to bolt that turbo onto my r33 s1.5?

depending on whether you are going hi mount or low mount u will need and external gate and pipe from somewhere to plumb it, oil line and the exhaust shop to make it fit your dump pipe.

How good a working order is the afm? Pink label... That a S2 RB25DET? Will u post to Sydney?

dont realy have time to get down to the post ofice but i will let you know but yes should be working as it was on my car before i went map sensor.

Link to comment
https://www.sau.com.au/forums/topic/367418-cheap-r33-parts/#findComment-5863448
Share on other sites

  • 1 month later...
  • 3 weeks later...
  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...