Jump to content
SAU Community

Recommended Posts

Ok, so the R34 GTR is now getting on a bit in terms of age and one of the things that doesn't last the test of time and the elements is the LCD screen on the multi-function display (MFD).

This was the case with mine - as you can see in the pictures below it was all cracked around the edges and was really annoying me.

IMG_40259web.jpg

IMG_40263web.jpg

So I started looking into what the reason for the cracking was and what options I had to fix it. After doing some forum research I found out that the problem is the polarising film on the front of the LCD cracks (due to heat/uv whatever) and this is what ruins the screen. There are 2 options -

1) Replace the screen with a brand new one - ~$200? (if you can find the right screen)

2) Attempt to replace the polarising film ~$20

I decided I'd have a crack at replacing the polarising film and after doing it I'd highly recommend if you have the same problem as me, follow my tutorial and do it yourself. Its just as much effort to replace the whole screen and is a whole lot more expensive. Even if you do have a go at replacing the film and you ruin your screen you aren't any worse of than you were before and you can replace the whole screen.

Before you begin you're going to need a sheet of the LCD polarising film. I bought the stuff from this place - http://www.3dlens.co...cdpolarizer.php and bought a 17inch piece and just cut it to size (which was good because I stuffed it up the first time and I had heaps left over to have another go). This is the film -

IMG_40291web.jpg

The other thing you will need for this job (apart from tools) is double sided tape - not the thick mounting stuff, the stuff that is just thin film between protective paper.

Ok, so once you have your supplies, you need to remove the MFD from the car.

Start off by pulling out your ashtray and unscrewing the one screw behind it. You should then be able to unclasp your gear stick boot and pull the whole plastic surround out. You will need to unclip the cigarette lighter.

IMG_40268web.jpg

Next, pull out the center air vent. Do this by carefully wedging a thin flat head screwdriver down the left hand side of the vent, and popping it out. I found using two works best - wedge one at the top of the left side and then use a second at the bottom of the left side and it will pop out. Unclip your hazard lights switch and pull the vent out.

IMG_40270web.jpg

Once you have the center vent out the plastic surround for the MFD will lift out of the way revealing the 4 hex head screws you will need to undo. Because they are near the winscreen you will probably need a stubby screwdriver, or, if they are as tight as the ones in my car were, and ratchet, socket and short extension.

Next, undo the 2 or 3 plugs on the back of the mfd - the brown and white ones need to have the little tab in the middle of the plug pushed down to pull them out. Levering them out carefully with a flat bladed screwdriver is the way to go.

IMG_40274web.jpg

Once undone, you can pull the whole unit out and move to somewhere more comfortable.

IMG_40275web.jpg

From memory, i think there's 4 screws around the unit and 2 on the underside you now need to undo to open up the unit. See all that stuff in there - that's why your home-made mfd never worked!

IMG_40278web.jpg

Ok, so you'll need to pull the ribbon out (by lifting the plastic clasp up) and also pull out the plug the blue wires are connected to. This will seperate the screen cradle from the rest of the unit.

IMG_40279web.jpg

Next, remove the screen from the cradle. Again the screws were super tight (I managed to destroy the head of one of them and had to cut a new groove with a hacksaw to get it out) so make sure you have a good quality, appropriately sized screwdriver to get them out.

Once out, you will need to remove the rigid plastic piece that is glued/taped onto the screen. Carefully run a knife around the edge making sure not to push the blade in too far.

IMG_40284web.jpg

Once the plastic piece is off the cracked polarising film is revealed. Clean the remaining sludge off the metal frame with the knife.

IMG_40286.jpg

Next, CAREFULLY, use the blade of a knife to lift the corner of the cracked adhesive film off the screen. It's stuck down pretty good and is quite hard to get it started so be patient. If you're not careful you will damage the actual screen itself like I did - if you only take a notch out of the corner it doesn't matter too much as you won't even be able to see it once you put it all back together.

IMG_40288web.jpg

IMG_40290web.jpg

Now I thought I'd go check I had the right film and that I hadn't damaged my screen up until this point, so I went and plugged it back into the car -

hmm.. so the polarising film is obviously important...

IMG_40292web.jpg

... and putting it the wrong way round won't help (don't worry it can only go on sticky side down)

IMG_40293web.jpg

that's it...

IMG_40294web.jpg

Ok, so with a sharp stanley knife cut your film to exactly the right size, peel off the protective film on the sticky side, and stick it down. I did this bit twice cos I ended up with a bubble the first time so I recommend sticking one edge down with the film bent and gradually laying it down onto the screen. If you screw it up you should be able to peel it back off carefully, cut a new piece of film and try again. Once on, peel the coating off the front of the film, line the metal frame with some new double sided tape and stick down the thick plastic piece: *make sure you put it back on the right way with the matt finish to the outside*

IMG_40298web.jpg

Put the whole thing back together again, unless yours is like mine and has fallen to bits as you pulled it apart. The plastic is really brittle and breaks very easily - araldite the broken plastic back together and nobody will ever know.

IMG_40301web.jpg

Install it all back in the car whilst trying to beat my time of around 6 minutes to put the screen, screws and all the trim back in. Check out your good-as-new screen and post up your before and after photos in this thread :)

IMG_40314web.jpg

  • 2 months later...
  • 2 years later...
  • 1 year later...

sorry to bring up an old thread....but did you use the glossy film or the matte film? there are both types for each size on that website?

thanks

  • 1 month later...

Hey mate, replaced the film last year and to the glossy film which is the one you will want. Personally haven't tried the matte film but the outer clear plastic will provide you with the matte finish so you would want it as clear/smooth as possible underneath with this film. The glossy one turns out excellent.

The product code on the 3dlens website is P17. Just type that product code into the search bar at the top and it should come up.

Hope this helps.

Hey mate, replaced the film last year and to the glossy film which is the one you will want. Personally haven't tried the matte film but the outer clear plastic will provide you with the matte finish so you would want it as clear/smooth as possible underneath with this film. The glossy one turns out excellent.

The product code on the 3dlens website is P17. Just type that product code into the search bar at the top and it should come up.

Hope this helps.

I used the matte finish turned out perfect and exactly the same. this is well worth the restoration. mine looks brand new again.

  • 5 years later...

Been several years since I read this thread, and bought the lens from 3dlens.

I finally got around to it today.  Went pretty smoothly, and I"m happy with the results.

I had a few issues - but nothing show-stopping.  I had some glue residue on the screen from removing the polarising layer - and some polarising bottom layer got left on the screen when I was peeling it off- requiring *very* careful removal with some 99.9% isopropyl wipes (thankgod i do electronics repair as a hobby).  I also unfortunately had some permanent damage to the LCD layer from the extremely damaged polarised layer - which left some marks on the screen which could not be removed.  However, once the new polarising layer was put on (be careful with that direction too - cos for me, it changed when you remove the protective layer) - and then the glass layer - it was barely noticable.

Overall, a pretty straight forward project - and I'd recommend it to anyone who has an MFD with still a 20 year-old screen.  Do it as soon as you see any weirdness - as the polarising layer is breaking down and may damage the LCD. I'd post some pics, but honestly, the first post covered everything required.   The only other thing of note was I used some thin sellotape double-sided material to hold the top glass/plastic layer on - as its what I had handy - and is very thin and durable (it's white on the outside with blue writing saying 'peel backing to expose adhesive').

Oh - one thing for anyone who cares - the the size of polarising film I cut out was 75mm x 130mm approximately - to give anyone in future an idea how much material you need.  I bought the matte 17" stuff - and it looks great, and had plenty of material leftover - especially handy as I did get caught with the polarising film being the wrong direction the first attempt.  It pays to double-check these things :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...