Jump to content
SAU Community

Recommended Posts

Hi Guys,

I just secured the last two sets of 18 x 10.5" +18 RE30 Clubsport that RAYS had available, they're in my shop in Japan ready to go in the next container which looks like packing this weekend.

Looking at arriving to Melb in approx 6 weeks or so, you can secure your set with a 50% deposit now.

I must reiterate - I already have these in our possession, this isn't an order with an unknown lead time from RAYS - so you pay your deposit and in around 6 weeks, give or take, they will be in Melb ready to pick up or ship out

$3500 the set, delivery available Australia wide or pick up from our shop when they get here. Can ship via EMS at additional cost :)

Pics now up :)

Cheers

Aaron

post-58515-0-45241500-1309155417_thumb.jpg

post-58515-0-68998900-1309155427_thumb.jpg

post-58515-0-60492000-1309155435_thumb.jpg

post-58515-0-79287900-1309155446_thumb.jpg

post-58515-0-87488000-1309155456_thumb.jpg

post-58515-0-70953100-1309155464_thumb.jpg

  • 2 weeks later...


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...