Jump to content
SAU Community

Recommended Posts

Stealth means asking on an internet forum..................hahahha.

Try mounting your switch under the dash somewhere? But one thing you don't want to do is have a switch that you have to bend to use - you need to be in your normal driver position and still be able to access it otherwise you'll look like your using a kill switch

I have a kill switch off the ecu area and I also have a battery isolator switch on a remote. My alarm - you could say - is direct feed to the battery so it is unaffected.

Link to comment
https://www.sau.com.au/forums/topic/370228-killswitches/#findComment-5901327
Share on other sites

i wouldnt discuss a kill switch on here, they can be so stealth you cant see them or touch them. RFID chips . Iphone bluetooth, IP the list is huge, it depends on your budget and know how.

not many places in OZ know how to do a RFID or proximity kill switch. that I have found. anyhow

kill switches can as easy as a cig lighter or something you never touch just your "presense" is all you need.

Link to comment
https://www.sau.com.au/forums/topic/370228-killswitches/#findComment-5901602
Share on other sites

Stealth means asking on an internet forum..................hahahha.

Try mounting your switch under the dash somewhere? But one thing you don't want to do is have a switch that you have to bend to use - you need to be in your normal driver position and still be able to access it otherwise you'll look like your using a kill switch

I have a kill switch off the ecu area and I also have a battery isolator switch on a remote. My alarm - you could say - is direct feed to the battery so it is unaffected.

thats the first place a crim will look, and a huge fail !!! and you just announced how to defeat your alarm to the world

Link to comment
https://www.sau.com.au/forums/topic/370228-killswitches/#findComment-5901607
Share on other sites

a crow bar fixes that, and most of the time theyll break into the boot looking for easy to take items if they can't start the car

then your car gets ransacked , best bet is to stop them BEFORE THEY BREAK IN using common sense

then a mutiple layer protection

and ultimate a GPS interface that can remote shut off the car next time the brakes are applied below a set speed, or geofence

Link to comment
https://www.sau.com.au/forums/topic/370228-killswitches/#findComment-5904682
Share on other sites

hate to say it but the last few 33s I have repaired from theft the boot was popped the pump relay bypassed and then the column smashed.

insurance is the best idea. some of the cars I do have remote relays on them and if they do not see a remote control signal they DO NOT work. google that. plenty of companies make them.

Link to comment
https://www.sau.com.au/forums/topic/370228-killswitches/#findComment-5906555
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...