Jump to content
SAU Community

R33 1995 Series 1.5 Gtst Turbo :) Cheap Cheap!

geraus
 Share

Recommended Posts

geraus Mentor

geraus

Posted
Posted (edited)

Hey guys its time to let this baby go! Selling due to upgrade!

I would also consider swapping for a Road Bike Sports Bike prefably a 250 + cash my way. Or willing to swap for a ute!

Nissan Skyline R33 GTST 1995 Manual.

Comes with:

17inch original volks japanese rims

APEXi SAFC II

Greddy Boost gauge

Bosch 040 Fuel Pump

Re-Turn Flow intercooler ( LEGAL )

Greddy 3inch Dump pipe

Hicas Lockbar

I'm Asking 8500ono.

Here are some pics! Very clean!

img1812v.th.jpg

img1813c.th.jpg

img1814m.th.jpg

img1815su.th.jpg

Edited by geraus
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
geraus Mentor

geraus

Posted
  • Author
Posted

yeah it has ABS

still up guys! car is imac!! need to sell this so i can drive my other 33! or if you guys have any nice bikes! im willing to swap!! bumppp!!!

7.5k!!

  • 3 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Did and sync timing with light 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...