Jump to content
SAU Community

Fs Vic: Bov, Rb20,

mothy87
 Share

Recommended Posts

mothy87 Rookie

mothy87

Posted
Posted

Up for sale I have a Turbosmart Supersonic BOV in near new condition. Comes with custom adapter to suit RB25 but also has original weld on adapter and box. $250

RB20DET complete motor with all bolt ons and wiring loom to suit in a R31. Turbo looks like it's been highflowed! Unknown condition as I brought it off eBay but never installed it as I went down different path! Was told had 96,000kms and ran fine $1000 have cooler kit to suit RB20 in a 31 as well for extra $200

R31 series 3 Ti complete front end conversion. Suggest respray maybe. It's white in colour $350

Full R31 Ti interior Inc. Trims, front & rear seats, door motors and regs, steering wheel. $300

Wolf 3D V4 Ecu in near new condition with hand controller, installation CD and disk. $1100

R31 blue colored wrecking complete car as well

May Have RB20DET gearbox with new exedy clutch and RB30ET turbo kit for sale soon

Link to comment
https://www.sau.com.au/forums/topic/371571-fs-vic-bov-rb20/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      R34 GTR Speedo Drive , sensor type ?

      By Butters · Posted

      Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • Duncan
      spot the stagea

      By Duncan · Posted

      roof rail delete used to be a thing, they were made locally for a while too
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • AnimalGarage
      Can you mount the ATTESA pump in other locations?

      By AnimalGarage · Posted

      According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...