Jump to content
SAU Community

Cant Get Oil Pressure

jarrod83

By jarrod83,
in Engines & Forced Induction

 Share

Recommended Posts

jarrod83 Community Regular

jarrod83

Posted
Posted

Hey Guys,

finishing my rb30 rebuild, it has a nitto oil pump, primed the system by filling up the outside hose of the oil cooler and cranking the engine backwards until it had sucked up a good 500ml of oil, left the hose off and cranked it over.

Absolutely none of the oil comes back out the hose almost like its draining straight through the pump, any ideas??

could the gasket that goes between the block and the oil pickup be leaking causing the oil to drain out of the oil pickup? or an airleak elsewhere on the pump causing the problem?

Jarrod

Link to comment
https://www.sau.com.au/forums/topic/371949-cant-get-oil-pressure/
Share on other sites
r33_racer Grand Master

r33_racer

Posted
Posted

Did you put assembly lube or vasoline in the pump gears to help it generate more suction?

Why did you crank it backwards to suck in oil for? If you put some lube in the pump gears and pulled the plugs and injector lead and just wound it over it should prime normally.

Did you disassemble the pump by any chance and forget to do something up or left something out maybe?

jarrod83 Community Regular

jarrod83

Posted
  • Author
Posted

didnt put in any lube or vaseline, was just told to prime it by filling the pump out section with oil and crank it back a few times.

The only thing im a bit sketchy on is oil pickup gasket, i think i may have used the old rb25 one as i found what looks like the new one on the floor when i was cleaning up and i had already dropped the engine in. If theres no other possible causes i may have to "attempt" to drop the cross member and remove the sump and try replacing it. I was kind of hoping that i may of had two new ones floating around as ive used a fair few gasket kits.

r33_racer Grand Master

r33_racer

Posted
Posted

I know you cant drop the factory sump off with the cross member still there. If you dropped the cross member you could do it. Ive tried this before and couldnt get it off while the cross member was there.

Might be easier to just pull it all out and double check that gasket if its a big question mark. It would have to be a big leak for it to not prime up.

jarrod83 Community Regular

jarrod83

Posted
  • Author
Posted (edited)

so you couldnt get it to pump oil by priming it and cranking the engine?? You had to actually start it to get it going?

I completely removed the oil cooler and standard oil filter backing plate and left just an oil filter using the rb30 threaded fitting. Drained the oil out of it and pumped it all back in through the 1/8th bsb thread on the side of the block next to the oil filter.. cranked it over and still nothing.

I might pump the oil back through the fitting and check that its getting to the head and try starting it for 5 seconds.

Edited by jarrod83
JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

my old motor wouldnt make pressure cranking, even with a used oil pump full of oil and heaps of priming. even after 5 mins of cranking there was nothing, started it up and had pressure within 2 seconds. sometimes cranking just isnt enough, aslong as everything was assembled with lube and oil in all the right places it can run for a few seconds without pressure without doing any damage.

jarrod83 Community Regular

jarrod83

Posted
  • Author
Posted

fk, cant believe it, but i primed the f*kker, started it, oil pressure just flicked straight up...

besides opening the oil pump and filling it with vaseline i couldnt have done any more to prime it for pressure, cheers for all the input guys, wouldnt of attempted starting it without pressure without it.

Jarrod

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 25GT Engine Light 21

      By GTSBoy · Posted

      If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • The Bogan
      SAU NSW - R U OK? Southern Highlands Cruise

      By The Bogan · Posted

      Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Duncan
      SAU NSW - R U OK? Southern Highlands Cruise

      By Duncan · Posted

      Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
×
×
  • Create New...