Jump to content
SAU Community

Recommended Posts

hey guys, i have a r33 gtst skyline and have just reciently intstalled the apexi PowerFC and hand controller. The rest of the car is pretty stock, except for 3in exaust. The FC is still in its base tune. What i have noticed though is if i give it a bit, it's not too hard to get the FC to flash up 100% duty cycle for the injectors (or close to it).

whats the most logical cause for this, injectors or fuel pump on the way out?

leigh.

Link to comment
https://www.sau.com.au/forums/topic/37231-100-injector-duty/
Share on other sites

Most logical cause is the the base map is set up for greater fuel delivery to take into account more mods than you have (ie is tuned rich).

Get it on a dyno and tune according to the air/fuel ratio. Will probably find that you'll gain power as well as reduce fuel consumption.

Link to comment
https://www.sau.com.au/forums/topic/37231-100-injector-duty/#findComment-745695
Share on other sites

Guest INASNT
just get GT-R injectors ,pump,FMIC,POD and youll fly .. 13 seconds garunteed.

that wouldnt cost you much.. how much boost are you running ? you must be on atleast 11psi to max out the injectors and fpump

bahahaha!!!

U have obiliously have not done any of these in your car have ya?

B33st

If u got stock everything else then ur injectors shouldnt be maxing out.

Get the injectors ultrasonically cleaned and checked coz they must be a blockage somewhere, or your fuel pump is cactus. Also if u continue to drive your engine will be pining up high with the base maps

Link to comment
https://www.sau.com.au/forums/topic/37231-100-injector-duty/#findComment-750702
Share on other sites

I have already purchased new 044 fuel pump, sx reg, surgetank. Also no the way are a Greddy Plenum, Q45 afm + throttle body.

Had just put the FC in and given it a bit or a run to see how it would go. Ran like normal, except for the fact that the hand controler was easy to get to show 100% duty, never showed more than 17 on the knock meter though.

as soon as i get the plenum etc, will installing all the bits and taking it to ARE (QLD) for custom cooler / piping job.

then its time for a tune, and i guess i will find out if new injectors are needed too.

leigh.

Link to comment
https://www.sau.com.au/forums/topic/37231-100-injector-duty/#findComment-751564
Share on other sites

yeah am working towards the turbo...

I wanted to do my build-up in 2 stages.

1. support systems

2. big turbo and big boost.

i pretty much have all the support items now(see last post). so ill get them installed + tuned and it'll then just be a matter of waiting till i have the funds for the turbo.

leigh.

Link to comment
https://www.sau.com.au/forums/topic/37231-100-injector-duty/#findComment-753226
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...