Jump to content
SAU Community

Recommended Posts

hi guys. just got my skyline back today. its a rb25-30 motor. standard head, standard rods and new cast mahle pistons.

he said he did one pull only on it after tuning. it made 450rwhp on 17.5psi and blew heaps of smoke out the back (think he said that) and was coming out the breathers on the engine.

he said the pistons would be fine for it (i already had the motor done and all that). after i got it home my engine bay is covered in oil from the breathers. (didnt have catch can on yet, just open breather pipes

if it turns out to be from detonation can i make him pay for new motor?

Edited by joe blo
Link to comment
https://www.sau.com.au/forums/topic/372437-new-engine-blown-up-at-tuners/
Share on other sites

  • Replies 218
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Is it actually broken (eg rattles and clunks) or is it fine except for oil coming out of the breathers?

no rattle and clunk noises im pretty sure. runs abit rough on idle and its different to start then before. hard to start but does go

has the 2 1.5mm oil restrictors put in and spool oil drain back kit for rear of head

what are you thinking? hope it may just be broken ring

Edited by joe blo

just a receipt from when i paid. about 4 weeks ago i got the car back. car wouldnt rev over 4500 in neutral and boost cut would hit at about 4000rpm if you could rev it that far and had boost cut from ecu at 20 psi. i had to ge the car back and take the wastegate off myself and fix the thread for the hose then put it on and go back to get the tune finished. in that time i put a 50mm gate on instead now but. today was the finish tune day

if it turns out to be from detonation can i make him pay for new motor?

What is this..... america???

You'r playing with modified engines... it happens. If you think your tuner did somthing wrong, don't take the next one to them..

Or was it the engine builder?

Or the injector manufactuer

Or the spark plug factory

oooor maybee it was the sneaky fuel supplier

hang on.. I have it-

Mr spanky with a candle stick holder in the sitting room.

This is some sort of Friday afternoon joke right?

Any tuner can only do his best with what he's given. If the setup (hardware inside engine) was crap before it got there, it wont magically get fixed on the dyno.

I was going to say that if its still running fine and not making any noises then it may be a lack of oil control thats got you so concerned

ah forgot that part. i put the crank in myself and couldnt get the rods and pistons in so got them put in at machining shop. then picked it up and assembled the rest myself

How was the motor run in?

Did the machine shop actually measure all the tolerances and so on, or simply assemble and return (which assumes you measured it all up).

cool. hopefully thats the case.

the problem will be shown when its pulled apart yes? it wont be mystery failure form me putting it together?

If it's pulled apart by a professional, then yes.

By the sound of it, and no offence, if you DIY you aren't going to find out.

How was the motor run in?

Did the machine shop actually measure all the tolerances and so on, or simply assemble and return (which assumes you measured it all up).

motor was run in on dyno by tuner guy.

the machine shop bored the block and supplied the pistons. and they measured the bearings and provided the ones i needed

the standard rb25 i pulled out had 6 broken pistons and didnt make ANY bad noises. drove it for like 1.5 years as a smoke machine and it made 250rwhp smoking HEAPS

if its from poor assembly i totally accept it. it was a learning thing. if its from me i dont think il bother learning anymore lol.

the big thing for me was going to be if it even started and worked properly in the first place. lol

after the first startup and first tuning went well i was convinced i had done a good job done properly

Edited by joe blo

Tell me which tuner in their right mind would pay for someones engine if it broke on the dyno? Almost anyone can slap a motor together and have it last for a couple of runs/weeks. You gotta know more about engine building than just bolting it together with the right torque settings.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...