Jump to content
SAU Community

Recommended Posts

So I've just bought a 2003 V35 Skyline, and had it shipped to WA from NSW by the dealer. I had it third party inspected, but never test drove it myself. The CD player does not work, and the CD I put in it is jammed, and makes a noise everytime I turn the ignition on. On top of that, I was told a band extender would be put on the radio, it was not. I am currently considering putting a tape in, just so I have something to listen to...yeah it's gotten to that point.

Looks like a band extender is $100-$200 and the CD jam will be $550-$650 according to these forums.

What can I reasonably expect to happen? Is the dealer obligated to cover the expenses I will incur fixing these things?

1st step is take it up with the inspector. It is their job to find these things out, and what you pay them for. The guy who inspected mine discovered the broken audio unit, so they replaced it. However my guy didn't realise the central locking didn't work and I never chased up anyone about it, so it still doesn't work (well, intermittently anyhow) 2 years later :(

Yes, every 2nd hand dealer has a statutory 3 month warranty on every vehicle they sell. If they don't want to play ball, tell them you have spoken with Consumer Affairs and they advised that the dealer fix it quick smart, otherwise they will be getting a letter from the ACCC.

My advice is if you can get the $600(ish) out of them install a Nissan double din kit and put a nice touch screen DVD player/radio in like I did similar to this : http://www.ebay.com.au/itm/260817904589?hlp=false

For a small amount of out of pocket coin you will have a good setup.

My advice is if you can get the $600(ish) out of them install a Nissan double din kit and put a nice touch screen DVD player/radio in like I did similar to this : http://www.ebay.com....04589?hlp=false

Disagree. The dealer is only obligated to 'make good'. In other words, if there is a CD player and the car is sold with all kit advised in working order then they are obliged to make it work - they can do this by installing a KMart special. And the guy who checked it out is just to ensure that no major issues exist and alert you to it so a decision is made with full knowledge *before* you commit. If they did not pick up this fundamental issue, then they may be worth pursuing but I suspect it's not worth your time - best spent on the dealer.

At the end of the day, it all comes down to how honest the dealer is. Some will go beyond their 3 month responsibility to maintain good customer reputation. That is what you need to work on. Mention that you have sought advice from this Australia-wide car forum as to dealer responsibilities, and that the consensus is that they must make good which is why you are pursuing this. Advise you are seeking OEM replacement. That may put the Fear of God into them and then you can negotiate a half-way with 2nd hand (but working) OEM - aim for kit from a Series 2 (it works better). If there is perception of lost business from others in the forum ( and word gets around), they may think twice in mucking you around.

But be careful to make it sound non-threatening (suck it in initially) - if they think they've already lost you they won't work so hard to keep you on-side.

Edited by Stuart McK
What can I reasonably expect to happen? Is the dealer obligated to cover the expenses I will incur fixing these things?

have you actually contacted the dealer to see what they say about it? chances are this was a waste of a thread and they will either fix it, or send you somewhere and pay the bill etc.

sorry to make this sound rude, but thats what will probably happen lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...