Jump to content
SAU Community

Ats Twin Carbon Plate

destrukshn
 Share

Recommended Posts

destrukshn Rising Star

destrukshn

Posted
Posted

Hi All,

I've got the above for sale. The clutch is still currently in my car so I am unable to take photos as yet. However, once purchase i can have it removed within a week. It is a clutch kit, so comes with a lightened flywheel and I'll add the push/pull converter.

Reason for sale is that clutch is currently slipping when i am trying to run 2bar boost. It is running 442awkw fine at the moment without slip and has only seen about 8000km, it hasn't seen any track days and really only street driving, the casual launch but in saything that, currently works fine. Clutch feels just like a standard BNR34 clutch with of course the extra grip. Flywheel has also been balanced before it was fitted in to my car.

Pictures of it can be found on Nengun link below:

http://www.nengun.com/ats/carbon-clutch

Price i am looking for is $1600. Nengun is selling for about $2753 (without the push/pull converter)

Link to comment
https://www.sau.com.au/forums/topic/374248-ats-twin-carbon-plate/
Share on other sites
destrukshn Rising Star

destrukshn

Posted
  • Author
Posted (edited)

Well the last time it was run, was on the powertune dyno, where i was running 1bar HKS actuators and it seem that the actuator couldnt hold the power. At the time i could only make 441awkw @ 1.5 bar with actuators set by electronic boost controller to 2bar, dropped to around 1.5bar with the car running fine on the dyno and without any slip at all.

It was running perfectly fine @ 441awkw, after i changed to 22psi actuators and set it to 1.8bar, slipped from about 6000rpm in third gear. Not exactly sure what power i would've been making at 1.8bar, possibly about 460-470awkw.

So if you aiming for about 450awkw which is pretty much most people running -5s, i'd say this is the perfect clutch for you, whereas my car will hit closer to the 500awkw mark.

Edited by destrukshn
destrukshn Rising Star

destrukshn

Posted
  • Author
Posted

450kw@4wheels -5's?? do you mean -10 gtrs?

No, i mean -5's. If i had a set of -5's on my GT-R now i am pretty confident i'd be able to push 450awkw out of it.

There are a few people on here who have had about 450awkw from 2530s/-5s.

I am running the Garrett -10 equivalents on my BNR34, the HKS GT-RS. In saying all this, i am running e-85..

Anyway, back to the thread, reason for selling is because i am looking to move to a triple plate :)

Any offers?

Tim GTR Proficient

Tim GTR

Posted
Posted

No, i mean -5's. If i had a set of -5's on my GT-R now i am pretty confident i'd be able to push 450awkw out of it.

There are a few people on here who have had about 450awkw from 2530s/-5s.

I am running the Garrett -10 equivalents on my BNR34, the HKS GT-RS. In saying all this, i am running e-85..

Anyway, back to the thread, reason for selling is because i am looking to move to a triple plate :)

Any offers?

I have got a brand new ATS triple carbon ear marked for the Veilside.not putting it in as the car has been detuned to stock 240kwaw, don't need this clutch. reserved for my GTR33 track car running GT35/40.Nismo twin plate

Alex 0433878905 Melbourne

destrukshn Rising Star

destrukshn

Posted
  • Author
Posted

whats the model number for that clutch? is it (CN23310-11)

CN23220-11 is correct! :)

I have got a brand new ATS triple carbon ear marked for the Veilside.not putting it in as the car has been detuned to stock 240kwaw, don't need this clutch. reserved for my GTR33 track car running GT35/40.Nismo twin plate

Alex 0433878905 Melbourne

Hi Alex,

PM Sent.

will only suit a R34 wont it ?

Hi Blitz-26,

Well it will fit anyone running the BNR34 Getrag.

destrukshn Rising Star

destrukshn

Posted
  • Author
Posted

why dont u get the CN23225-14 will that hold because im hoping to make the same power and i was looking at the same 1

I might, however, hoping i can sell out my one first and i'll order a new one :)

Lots of questions, but no one interested yet!

Come on guys, great clutch, near new condition! I dont even ride the clutch, not my driving style! :)

SS8_Gohan Grand Master

SS8_Gohan

Posted
Posted

have one of these in my 34, brilliant clutch. Running 400rwkw and plenty of torque (E85) and all seems fine :)

very streetable clutch that can still handle a fair whack of power/torque

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Turbodoc
      Noobie Stagea owner..

      By Turbodoc · Posted

      Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • GTSBoy
      Duncan's V37.......race car?

      By GTSBoy · Posted

      See if you can thermal epoxy a heatsink or two onto it?
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...