Jump to content
SAU Community

Recommended Posts

Hey all my girlfriends R32 has had 2 motors die in her r32 and now she is deciding to drop a 25 in there so we have a heap of cheap parts that are up for sale, i'll start with a few things i can think of and add to the list as i find more stuff:

First RB20 (130,00K's)

Blown head gasket and exhaust valve, currently dismantled;

Bottom end is not that bad but the exhaust valve landed in the first piston bore and made some gouges in there :(

Head is seemingly fine except the exhaust valve will need replacing... offers on these two!!

Cams in perfect condition $ Offers

Second RB20 (76,000Ks)

Low Compression on 6th ran fine though just lean in the top end :(

Head is perfect (Just Tested) $250

Intake manifold $ Offers

Exhaust manifold (Just replaced with perfectly straight one) $100

Perfect Condition Cams $ Offers

Bottom end needs rebuild $ Offers

Also these Items;

1X RB20 turbo in decent condition $100

1X RB25 turbo in good condition minimal shaft play $250

1X RB25 turbo suit rebuild, held boost fine just a bit smoky every few days $ Offers

2X RB20 ignitor packs $ Offers

5X Rb20 Coils seem fine just installed one in my motor and it runs fine :) $25 Each

9X RB20 Injectors 6 are known to run fine 3 i've never driven with so may need to be tested $ Offers will sell lot or individually

1x RB20 Rocker Covers Painted metallic black $100

1x RB20 Rocker Covers silver oil hose connector is broken on one needs welding $30

1x RB20 Good condition Exedy Heavy Duty Clutch $ Offers

1x RB20 flywheel $80

1x R32 standard rear bar pretty beaten up Silver colour $50

1x pair of Monza front R32 shocks Good condition sit at a nice low height, top adjusting nut of one is damaged $150

If you are chasing any RB20 parts or wiring PM me here and i'll let you know if we have any ;)

Cheers, Tobbie 0418510695

Edited by tobs_r32
Link to comment
https://www.sau.com.au/forums/topic/374464-tons-of-rbr32-stuff-for-sale/
Share on other sites

I'm in Hobart area Sven. And yeah tof I only had it running in the car for around 6 or 7 hours and didn't really notice it until my mechanic went to tune it and compression tested it. It's pulled apart at tad engine reco atm

I'm in Hobart area Sven. And yeah tof I only had it running in the car for around 6 or 7 hours and didn't really notice it until my mechanic went to tune it and compression tested it. It's pulled apart at tas engine reco atm

yep cool, do you mind if i ring them about it? , how much are you chasing for it?

not a lot dude, after being buggered around so much myself with dodgy second hand parts i wouldn't do it haha! The head was fine and passed all the tests but mark was saying the bottom end is just worn and needs a pretty decent rebuild. I brought it off a guy on here as a fully working RB20 and only had it in a car for a few weeks. What are your plans for it??

NEW UPDATED LIST;

First RB20 (130,00K's)

Blown head gasket and exhaust valve, currently dismantled;

Bottom end is not that bad but the exhaust valve landed in the first piston bore and made some gouges in there :(

Head is seemingly fine except the exhaust valve will need replacing... offers on these two!!

Cams in perfect condition $ Offers

Second RB20 (76,000Ks)

Low Compression on 6th ran fine though just lean in the top end :(

Head is perfect (Just Tested) $250

Intake manifold $SOLD only the top half sold, still have sensors, 2x bottom manifolds etc.

Exhaust manifold (Just replaced with perfectly straight one) $100

Perfect Condition Cams $ Offers

Bottom end needs rebuild $ Offers

Also these Items;

1X RB20 turbo in decent condition $100

1X RB25 turbo in good condition minimal shaft play $SOLD

1X RB25 turbo suit rebuild, held boost fine just a bit smoky every few days $ Offers

2X RB20 ignitor packs $ SOLD

5X Rb20 Coils seem fine just installed one in my motor and it runs fine :) $25 Each

9X RB20 Injectors 6 are known to run fine 3 i've never driven with so may need to be tested $ Offers will sell lot or individually

1x RB20 Rocker Covers Painted metallic black $100

1x RB20 Rocker Covers silver oil hose connector is broken on one needs welding $30

1x RB20 Good condition Exedy Heavy Duty Clutch $ Offers

1x RB20 flywheel $SOLD

1X RB20 ECU - $SOLD

1x R32 standard rear bar pretty beaten up Silver colour $50

1x pair of Monza front R32 shocks Good condition sit at a nice low height, top adjusting nut of one is damaged $150

1X Perfect RB20/S1 RB25 AFM - $120

Coil Pack Looms - Sold

1x RB20 Intake pipe $40

4x Rb20 Cam Gears $20 each

1x Standard RB20 Coil Pack cover

1x R32 Reo plate for behind the backseat with bolts $50

Still have more wiring and sensors in good condition if your after any ;)

Cheers, Tobbie

Edited by tobs_r32
  • 4 weeks later...

Sill have most of this stuff and more!! Make me some offers!!!

Also have;

2x CAS - $offers

1X Pioneer CD Player good working condition $30

1X R32 straight pipe from the front pipe back (Decat as well) has all the hangers on it mounts up nice.. sounds ANIMAL!! $50

1x Front pair of ISC N1 coilovers 9 months old (7,000ks) Currently being rebuilt $500

1x Rear pair of bilstein Adjustables good condition $300

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...