Jump to content
SAU Community

Nismo vs other short shifters

Greg

By Greg,
in Engines & Forced Induction

 Share

Recommended Posts

51jay Mentor

51jay

Posted
Posted

I've got C's, It is very good, solid works well and is very easy to fit. As far as I know Nismo make two one of them shortens by only 10% the other I Don't know, quality should not be a problem though

Greg Veteran

Greg

Posted
  • Author
Posted

OK i've been doing some research and it looks like there are basically two types of shifters:

- Short Shifters (aka solid, direct)

- Quick Shifters

What's the difference?

From the pics I can see of the two, the short shifters just shorten the stick, while the quick shift kits come with a shortened stick and also a whole lot of other nuts, washers and brackets etc (i'm not very good at technical stuff:D).

If any would care to explain I'd appreciate it. Thanks!

Summary so far: C's is the way to go

51jay Mentor

51jay

Posted
Posted

I got my C's from takakaira.com in Japan delivered to my door took 2 weeks cost $A634 via credit card.

The proper short shift changes the length of the stroke at the bottom of the gearleverwhich actually makes the change faster and also has the effect of shortening the length of the arc your hand moves through when you change gear. Just shortening the top of the lever shortens the arc but doesen't change anything at the bottom.

Currently I'm thinkinf of shortening the top of my C's .............Has anyone else tried this. It should give a really short shift but might make it a bit too stiff.

51jay Mentor

51jay

Posted
Posted

| Hype ^ | yes that's the idea would make for a double shoetening of the arc your hand moves through. Was also thinking of fitting a gate in the top of the console instead of the leather boot like in some Ferraries.

hitnrun Collaborator

hitnrun

Posted
Posted

A short shifter is simply that, the distance between the pivot point and the gearknob is shorter.

A quick shifter has the pivot point changed so the throw required to change gears is less as well as the stick being shorter, however it also means it is stiffer, or firmer to change. Most people prefer this and the difference is usually not that great. Imagine a see-saw with the hinge moved to one side. Same principle. Just think, all those physic's lessons are paying off :)

If you have ever been in an excel with a really short gear stick, it usually means that is has had the top hacked off with a cheap fake momo glue back on top. If you have even driven a car like this you know that it makes changing gear really ****. Only spend money on a quick-shifter kit if you really need it. I mean the skyline shifters aren't too bad in the first place.

The C's shifters use adapters to change the pivot point, another way of getting a shorter shifter is to remove the ball joint from the shifter and have it reattached futher along the stick.

Anyway never complaint about the length of the Nissan shifter until you have driven old school 4wds. Most seem to have about 2.5metres of throw.:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • myrbgivesmeheadaches
      RB25DET NEO Cylinder Head

      By myrbgivesmeheadaches · Posted

      Did this end up working? Did you take some pictures?
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...