Jump to content
SAU Community

Recommended Posts

  • Replies 182
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

That's the idea, people who buy these sort of cars IE those interested in resale value etc buy the car new, live with it while under warranty then get rid of it before it has problems.

That's sort of how manufacturers want it to work anyway.

euros are definately overpriced and so are bought by people with disposable income who are happy to buy disposable cars..the more expensive euros however are better quality machines because people that spend quarter of a mil on a car expect it to last....

Most jap branded cars I find are good for 250kms before they start to fall apart..

You make me laugh.

Why? Cause I speak the truth?

Take a 10 year old Jap car and compare it with a 10 year old euro, see which is better. The jap car will still drive like new, trims intact etc the euro will have trims falling of, engine light on dash, rooted box if its a auto, trust me i work on euro trash everyday and its complete rubbish.

The only good euro's are porches or high end stuff, the low end euro stuff is awful.

Point been, most owners who love them only own them for the warranty period, so its a new car, but just wait till something goes wrong outside warranty period and you had better lube up.

Have you ever owned a Golf?

It won so many awards for a reason . . .

Lol, are people really that ignorant?

I have not and never will own a VW, I worked on vw's for over 5 years and I have seen it all, it makes me laugh that the general public still think there good.

The awards dont go into reliability or repair costs, if it did they would be behind most other makes.

Edited by eightsixboy

Why? Cause I speak the truth?

Take a 10 year old Jap car and compare it with a 10 year old euro, see which is better. The jap car will still drive like new, trims intact etc the euro will have trims falling of, engine light on dash, rooted box if its a auto, trust me i work on euro trash everyday and its complete rubbish.

The only good euro's are porches or high end stuff, the low end euro stuff is awful.

Point been, most owners who love them only own them for the warranty period, so its a new car, but just wait till something goes wrong outside warranty period and you had better lube up.

Any car that isn't serviced / neglected us going to fall apart. I've had both jap and euros (E39 540i, E36 M3 Evo, Audi 80 <2k bunky, nothing broken), both are totally different to own and drive. Jap cars feel so cheap in comparison to euros.

My mum has had a C280, Saab 95 and currently a E39 528i. All trouble-free, looked after, reliable solid cars.

But there is a big difference between a 40k BMW and 20k VW. Of course any car that is looked after will be reliable, but jap stuff will last longer and be alot cheaper to fix.

I have driven alot of cars including a Gallardo, R8's, R36's RS4's Golfs etc and there boring compared to a GTR or even my GTST, thats my opinion but everyone at work that drove the Gallardo said it was a piss of crap, an expensive one at that.

Problem is most people dont have 5k plus to replace there gearbox when it does need replacing (which it will) or 1k do do a service on them, yes they might drive well but there way overpriced to fix and service, and when they do break it can cost a crap load.

I knew a guy who worked at Saab and he hated them, having the cambelt facing the firewall... wtf are they thinking. I guess when you work on these cars you develop a hatred for them I guess, but its just funny how knowone at my work actually drives euros, the only ones that do dont have to buy them, kinda says it all.

Edited by eightsixboy

Thats fine, thats your viewpoint. But they are definitely not pieces of shit :)

edit: Pieces of shit can be landrover freelanders... Do not ever buy one, lol.

Yup fair enough, I just dont want this guy to end up buying a golf out of warranty and end up having 'issues', has happened many times before.

id go the Mazda 3 MPS. the VW golf is too expensive to maintain and repair (if it never needs any repairs. the golf also has shitty manual back seat adjuster/recliner knob which is another negative)

Ive seen ford Focus XR5 run at high 14s, low 15s which hard exhaust anf fmic from what i could see - pretty slow imo lol

actually doin the research for a relo that seems to have golf hype syndrome..personally I wouldnt even consider it as I dont like low end euro trash at all..

When we bought our honda accord a friend bought an A6 aud... Both 04 models both v6 both fully optioned with leather sunroof tint etc...the audi did look a bit slicker with its 18 inch wheels but didnt necessaarily handle any better.maybe at autobahn speeds but Ive had the honda on long drives happily at 120 to 150 and its still smooth as silk .audi did have a very smooth almost seamless 7 speed auto but it didnt have Vteck yo' so it wasnt any faster. The ride quality wasnt any better..audi did have a quieter cabin I beleive..but all in all he paid 40k when we paid 20k and I really didnt see the extra worth and his servicing is twice as expensive..maybe euro quality is slightly better but mostly its just bragging rights your paying for..

160,000kms on the accord now and other than tired shocks and the front discs needing machining which is common with all auto cas, I cant fault it..did have a door lock jam up but only cost me 40$ to fix

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...