Jump to content
SAU Community

Recommended Posts

Time to clear out the shed and getting rid of all the GT-R parts I have collected over the years. I have the following available:

First up is a complete cylinder head with plenum, exhaust manifilds, cam covers, basically everything is there to bolt up to a block. Fuel injectors, coil packs, crank angle sensor and turbos are all that's missing to make it a complete top end. This head has undergone some major custom work by Racepace Motorsport and is basically a one off. It has been reconditioned with new valves and most importantly has had some port work which resulted in valuable gains. The power came on earlier and also benefited from top end aswell. This costed me a considerable amount of coin so those of you who are after a basic head need not apply. The head uses standard cams which worked really well with the modifications to the head and also benefits from keeping the engine sounding and idling standard, good for keeping away unwanted attention. This head came off my car which had done around 500kms of street driving, I have not used this on the track, so basically it's like new. It also has Racepace adjustable cam gears(500kns old).

PRICE: $3200 ono for everything mentioned above...

Xforce stainless split dumps suit R32, R33 and R34 GTR, used but have no cracks, in very good condition.

05072011337.jpg

05072011338.jpg

PRICE: $300 ono

Series 3 GT-R gearbox with transfer case. This gearbox was rebuilt with new bearings and series 3 synchros and has done approx 2000kms. The transfer case has been modified by Racepace Motorsport to give extra torque to the front wheels. Made a big difference on the track as the car had much more stomp out of the slower corners. It had fresh redline oil put in it when it got rebuilt.

PRICE: $2750 ono

Cusco front adjustable upper control arms suit R33 and R34 GTR only. These have been modified by Racepace Motorsport to improve turn in. Can achieve -3.5 degrees of camber using standard lower control arms. Used but in very good condition.

PRICE: $450 ono

TEIN Circuit Master RS coilovers suit R33/34 GT-R's only. These were revalved and rebuilt to Racepace's custom specifications, and has also custom spring seats to accomodate custom springs. They are a worthy investment for any track orientated car. They are also an awesome package for the street, not that harsh of a ride considering how good they are for the track. I have done a 1:18.7 at Sandown with this setup so definetly worth the money.

PRICE: $4250 ono

R33 GTR short motor, includes N1 water pump (near new), oil pump, balancer, crank, rods and pistons. Was compression tested before being removed from car and was down on 2 cylinders. Its a standard bottom end and the block has not been machined. Ideal for someone wanting to rebuild an engine on the side without having their car off the road.

PRICE: $850 ono

R34 GTR standard sump and diff. Came off an engine that had done 72000kms. In very good condition.

PRICE: $800 ono

Standard RB26 cylinder head out of an R33 GTR, has been crack tested and is OK, suit reco, no cams, cam covers, valves, springs, shims, retrainers. Bare head only but has had a dash fitting pressed in for oil drain at the rear. Has slight markings on journals as pictured below.

31072011407.jpg

31072011408.jpg

31072011411.jpg

31072011412.jpg

31072011414.jpg

31072011406.jpg

PRICE: $300 ono

Currently all items are located in Narre Warren North in VIC, but will post items interstate at buyer's expense.

PM or reply here if interested.

Cheers,

Jack

Hey mate.

Interested in the block and bare head.

Does the block come with windage trays and crank girdle?

What does the crank look like? Any damaged big end bearings? Able to reuse the crank without linishing?  Brad

Edited by Just_a_datsun

Hey mate.

Interested in the block and bare head.

Does the block come with windage trays and crank girdle?

What does the crank look like? Any damaged big end bearings? Able to reuse the crank without linishing?  Brad

Hey Brad,

Yeah mate, windage tray and crank girdle are all there. Basically only the head and sump were removed.

This was a running engine before pulled out of the car. Was down on compression on two cylinders but after removing the head could not see any damage to the rings so not sure why it had low compression. There is no damage to the crank or bearings.

Are you in Melbourne? If so you are more than welcome to have a look.

Cheers,

Jack

Am I reading correctly. $4250 for second hand coils?

Yep, if you want stuff from racepace, you'd better open your wallets as they aren't cheap.

Best of luck in selling your stuff jack, and you gotta take me a ride in your GTR!

Anything to do with GTR's ain't cheap!!!!!

These coil overs are not off the shelf items, in fact they are discontinued and not available new anymore. They have been totally rebuilt and customized to be exceptional on the track aswell as on the street.

I understand that they are not for everybody, but those in the know will vouch for their performance and the price that goes with it....

More PM's replied.

Cheers,

Jack

No, unfortunately I am in Brisbane, hence the 20 questions.

Would you consider delivering the engine to a courier depot (would need to be on some sort of palet that they can forklift)?

Or better yet organise transport to brisbane?

Brad

Edited by Just_a_datsun

Hey Brad,

Putting it on a pallet and sending it up to you will not be an issue.

Can you send Private Messages yet? I think you need more than 5 posts.

If you can send me your email address I can send you photos and more info.

Cheers,

Jack

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...