Jump to content
SAU Community

Recommended Posts

Hi all;

I actually thought my gearbox was rooted but thanks to an hours browsing and searching around on the forum, I found out that there are two cylinders that exist and when i went to check my car, the master was bone dry. I filled it up with brake fluid and the clutch is working better now (still not as good as before but much much better ... I tried looking for a leak but its all bone dry near the cylinder and also near the footwell. I drove for around an hour round trip and came back and the fluid was still right where i topped it up till.

My question is, should I bother replacing the master and slave cylinder or wait to see if it gets empty again? Or just go and get it bled and looked at once from a mechanic when I'm getting my gearbox oil replaced?

Thanks for your help :)

Link to comment
https://www.sau.com.au/forums/topic/375765-clutch-master-cylinder-empty/
Share on other sites

When you say "footwell", did you mean inside the car? Because if you didn't then go look for brake fluid running down the inside of the firewall into the carpet and sound deadening. If you lie on your back with your head under the steering column and run your hand over the clutch pushrod (runs between the pedal and the firewall and passes through a rubber boot at the firewall) and you feel fluid, then the master has been bypassing internally and leaking out its back side. If you don't find any trace of fluid in the car, then it is probably the slave that has leaked it out. Get under the car and look for evidence around the slave. If it's been leaking there it should be fairly obvious.

If not - drive it for a week or two, check it every time you get in or out of the car, and see what happens. If the fluid goes away again, then get to a mechanic and get it fixed. Not having a clutch is a massive pain in the arse.

Yes I meant inside the car. The pushrod (if thats what its called) did have a bit of liquid at the end near the rubber seal (on the firewall end) but I'm guessing thats normal? I'll get the slave checked out while the gearbox oil is being replaced. If the fluid does not decrease after a couple of weeks, I should still get the system bled out correct?

Thanks for your input.

My R32 GTR had a leak from the clutch master cylinder that took about 1-2 weeks to notice a drop in fluid level with no obvious/noticable leaks.

Replaced the master cylinder and all good for about a year or two and then the booster stopped doing it's thing and had an intermittently hard and then soft pedal.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
×
×
  • Create New...