Jump to content
SAU Community

Recommended Posts

Hey guys,

Quick question. I purchased some Injector Dynamic ID2000s with the adaptor kit to suit. Is there any clips to hold the adaptors onto the injectors or do they just sit tight with the O rings & I've noticed alot of guys with these injectors have purple adaptors whilst mine a silver ( Is there any difference between the two colours or is just cosmetic). They are 11mm adaptors to suit my HKS rail.

Anyone with some knowlege on these would be great.

Cheers guys

Link to comment
https://www.sau.com.au/forums/topic/375869-id2000/
Share on other sites

Did you purchase the injectors from injector dynamics or someone local? If you bought genuine ones they would've come with the clips to hold the adaptor to the injector... Does your silver adaptors have a filter in the top.. If bought locally with non genuine adaptors there more than likely Bosch 2000's not ID2000...

Link to comment
https://www.sau.com.au/forums/topic/375869-id2000/#findComment-5994568
Share on other sites

They were purchased through VPW Australia ( http://www.vpw.com.au/productgroup.asp?CatID=6&SubCatID=1047&priorCatID=1047&PrdGrpID=5009 )

I spoke to them today but they didnt have any clue....

Here are some picture of them:

IMG_0440.jpg

IMG_0439.jpg

Is there any real difference between the Bosch ones and Injector Dynamics?

According to VPW they dont use clips at all but none shown on the ID website dont have clips.

Link to comment
https://www.sau.com.au/forums/topic/375869-id2000/#findComment-5995985
Share on other sites

They were purchased through VPW Australia ( http://www.vpw.com.a...7&PrdGrpID=5009 )

I spoke to them today but they didnt have any clue....

Here are some picture of them:

IMG_0440.jpg

IMG_0439.jpg

Is there any real difference between the Bosch ones and Injector Dynamics?

According to VPW they dont use clips at all but none shown on the ID website dont have clips.

depends who is selling what.. sellers of Bosch will say no difference

Link to comment
https://www.sau.com.au/forums/topic/375869-id2000/#findComment-5996177
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Update: O2 sensor in my downpipe turned out to be faulty when I plugged in to the Haltech software. Was getting a "open circuit" warning. Tons of carbon buildup on it, probably from when I was running rich for a while before getting it corrected. Replaced with new unit and test drove again. The shuffle still happens, albeit far less now. I am not able to replicate it as reliably and it no longer happens at the same RPM levels as before. The only time I was able to hear it was in 5th going uphill and another time in 5th where there was no noticeable incline but applying more throttle first sped it up and then cleared it. Then once in 4th when I slightly lifted the throttle going over a bump but cleared right after. My understanding is that with the O2 sensor out, the ECU relies entirely on the MAP tune and isn't able to make its small adjustments based on the sensors reading. All in all, a big improvement, though not the silver bullet. Will try validating the actuators are set up correctly, and potentially setting up shop time to tune the boost controller on closed loop rather than the open loop it is set to now. Think if it's set up on closed loop to take the O2 reading, that should deal with these last bits. Will try to update again as I go. 
    • More so GReddy oil relocation kits, sandwich plates, etc. all use 10AN fittings. And same, I've only used 10AN and my car sees track work (circuit, doing laps, not 10 sec squirt business).
    • street use or race track, what hose size and why? what factors change with the hose size options ?   see most comon is an10. when you see most oem external coolers are closer to an12? does high volume oil pump like nitto need an12 or 10 be just fine
    • The rod I was moving left and right you can see looking from the passenger side floor up into the center console.  IMG_8095.mov
×
×
  • Create New...