Jump to content
SAU Community

Recommended Posts

For sale is my new unused rb26/30 built this for my daily but lost my licence so no longer need it located in Hobart Tasmania but can send anywhere in Australia cheaply

Rb30 vl block

Chemically cleaned

Resprayed black

Tapped for gtr head studs

Decked

Bored 40 thou

Torque plate honed

Rb26 head reconditioned completely by Lewis race engines sydney

Acl steel head gasket

Tomei metal intake gaskets

Complete rb26 plenum and throttles

Arp head bolts

Hastings chromolly piston rings

New oversized pistons

H beam conrods

Arp conrod bolts

Acl bearings

Balanced crank

Jun crank cooler

Crank grub screwed

Rb25 oil pump

New front and rear main seals

Gates timing belt

Chemically cleaned rb26 cam cover set with speedflow fittings fitted to the creatures

Cost over $6000 to build after $4000 Ono need a fast sale to fund my main project please email [email protected]

Link to comment
https://www.sau.com.au/forums/topic/376137-fs-rb-2630/
Share on other sites

It was for a vl commodore to replace the rb30et and if I separate the head $1500 it cost $1800 - $2000 plus postage from Lewis engines from memory pm me numbers and i ring people that are interested must be sold in the next couple of days

Link to comment
https://www.sau.com.au/forums/topic/376137-fs-rb-2630/#findComment-5999815
Share on other sites

  • 4 weeks later...
  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...