Jump to content
SAU Community

Recommended Posts

sorrie i made a mistake on my last post by saying they was 18".

Swap 17x9.5" dift teks + 18 off set.

In black

swap for 17" or 18" with abit lower off set looking for jap wheels or sell $1600

wheels are in sydney

sms or call for pixs 0406139299

post-87758-0-74088200-1315902469_thumb.jpg

post-87758-0-47534300-1315902540_thumb.jpg

Edited by Ands151
Link to comment
https://www.sau.com.au/forums/topic/377057-fs-or-swap-17x95-18-drift-teks/
Share on other sites

also, for the 1600, does that come with better tyres than pictured?

just wondering as new can be had for around the same price(without tyres though)

<br />no worries, just offering some perspective...<br />like i said, ill grab some photos of the wheels i have tomorrow<br />
<br /><br /><br />

ok great i look forward to seeing the pixs, size and also how good are your tyres?

i got 2 brand new gt radails 235/45 r 17 tyres this week end the other 2 tyres are fair condition,

looking to swap with r33 gtr wheels or evo 5,6.7,8,9 wheels with good tyres. or something jap with less off set maybe + 35- +42 off set. 17" or 18"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...