Jump to content
SAU Community

Recommended Posts

I recently (and regretfully) bought my mrs an S14 series 1 in Auto. It's as clean as you can get, with 180,xxx on the speedo and full service history to go along with it. It's the luxury model so it has the sunroof, the different front bar with the fog lights etc. The motor is as stock as a rock, and the only modification is a cat-back exhaust - other than that the car is in factory condition. The car is completely unmolested, never been boosted and never even had a front-mount intercooler because the battery tray is still in tact and untouched. If you want a car that's "worked off it's tits", then close this window. If you want a car that's been very well maintained throughout, then send me a PM

Apparently, the car makes her look like too much of a "Maria" so she doesn't want it... She'd rather drive her Proton GTI (go figure), so now I've cracked it and I'm sick of driving my TX3 around - I want a manual turbo car for myself.

I'm asking $7,000ono only because I know the condition of it. I'm not in a rush to sell it, but I'm interested in a trade for possibly a 180SX or something within a similar price range. Open to any inspection, bring it on

Will get pics up within the next few days. PM me or call/SMS 0488-582-587. Willing to swap for a stock/clean 180 (prefer type-x) in manual + cash either way depending on condition.

Edited by stawka
Link to comment
https://www.sau.com.au/forums/topic/377058-eoi-s14-s1-luxury-spec-vic/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...