Jump to content
SAU Community

Recommended Posts

need your help fellas!

Looking to purchase a polisher, deciding between the GEX125 AC Pro and 150T. i know the 150 has a polisher setting, but between the two models the specs looks around the same. i was thinking the 125 would be better for the tighter spaces when polishing.

What are your guys opinions?

Thanks in advance!

Link to comment
https://www.sau.com.au/forums/topic/377405-bosch-gex125-vs-gex150t/
Share on other sites

bit pricey though, i special ordered mine through bunnings - showed them the price etc for it off sydneytools and they beat it by 10% .. thats the best deal I could get it for!

I dont use any backing plate :) the FI pads fits mine just right

Yeap, as long as you mask up the rubbers well i managed to do everywhere. most machines are too big for everywhere really and you still need to give some spots a good hand polish

If you are looking for a Random Orbital that has interchangeable backing plates and more power that the GEX150T but costs $229 you might want to look at the Concours 900 Polisher at Waxit Car Care.

You can also find a range of kits to go with the Concours 900 Polisher HERE.

If you are looking for a Random Orbital that has interchangeable backing plates and more power that the GEX150T but costs $229 you might want to look at the Concours 900 Polisher at Waxit Car Care.

You can also find a range of kits to go with the Concours 900 Polisher HERE.

that actually looks pretty cool i want to try but no point having two RO's!

  • 1 month later...

I bought the 125 and then realised that it was no where near as effective at the 150T as the 150T has both the forced rotation mode (which is what you want) and random orbit. Went out and bought the 150T, as stated before Final Inspection highly recommend this unit, and it makes a big difference having a unit that can do forced rotation. I had to have the 125 held lightly against the cars surface otherwise it would bog down and just vibrate on one spot.

having struggled with an old Bosch RO only and then upgrading to a 150T, forced rotation is DEFINITELY the way to go.

a few friends have gone to Rotaries and didn't find them as scary as they thought. Obviously need to be more careful, but they said they're soo much quicker again of their prev units (Rotex jobbies $$$) - depends how serious you think your hobby is going to get :D

scr34min order it from bunnings, if you show them the price of it from sydneytools bunnings will beat it by 10% .. :D

thats what i did

also im in perth as well ... with a gex150T + pads + polishes sitting around ..

i do need to order the heavy cutting pad/polish still though

ive only got medium and extra fine ones atm

if you need any help or anything let me know :)

i have exams real soon but after that I should be quite free ...

^ i got mine for about 350 ..

no pads though

but from melb you'd have to pay delivery and whatnot ...

about the same really hahah

if you go down the bunnings route

http://sydneytools.com.au/shopexd.asp?id=1243&bc=no

show them that :)

oh yeah, i remember paying around $360 now that i think about it....

but still, $50 worth of pads in there, plus whatever was postage on them.

but yeah, probably the best deal for Melbourne ppl

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...