Jump to content
SAU Community

Sexy GT-R at Autosalon

krzysiu

By krzysiu,
in Victoria

 Share

Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

JAGR33 Grand Master

JAGR33

Posted
Posted

Most of them go back to the place did the work on the car, for example, the gold 200sx went back to 'Racing Project' in Mitcham, and the celica that won 'King of AS' went back to 'Wolf Auto Design' in Clayton....

Got pics but don't know how to insert them in posts..... can anybody help??

Or should I put them in the members galleries???

Al Grand Master

Al

Posted
Posted

The only thing i did not like about that particular GTST was the side-skirts. They appeared to be designed for a wide-body kit as they went half way up the wheel-arch and stuck out about 20mm. If the kit was complete or the side-skirts were different, it would have been awesome.

Anyone read the artical in the free Auto salon mag., about what is rice?

To me this was a very clean car with alot of money spent on it. But it's disappointing to know that it will not be driven, which defeats the purpose of having a nice car.

ABuSD Veteran

ABuSD

Posted
Posted
The only thing i did not like about that particular GTST was the side-skirts. They appeared to be designed for a wide-body kit as they went half way up the wheel-arch and stuck out about 20mm. If the kit was complete or the side-skirts were different, it would have been awesome.

AGREED have a look @ the pic below the rear guards dont flare out all the way to the bottom of the car it goes back in, doesnt look good, and i think the GTR widebody straight kink ontop of the wheel arch is alot wider than the one on this GTS-t. I still like this car tho, dont get me wrong, but the GTR badges have to go!!

showphoto.php?photo=2730&password=&sort=1&cat=500&page=1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...