Jump to content
SAU Community

Help

SPOIL3D

By SPOIL3D,
in South Australia

 Share

Recommended Posts

SPOIL3D Rookie

SPOIL3D

Posted
Posted

My vacume hose on my Turbo Smart Eboost2 has a small split in it, Sucks because all i hear is a hissing noise (ssssssss) :(. does anyone know if its easy to change it yourself or know anyone that can change it for me?

*Note, would rather someone do it for me or atleast look over me so i dont f**k anything up.*

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/377900-help/
Share on other sites
rad100 Grand Master

rad100

Posted
Posted

hardest part will be feeding it through the firewall to the solenoid in the engine bay.

if you tape the new hose to the old hose and pull it through it will make your life 100% easier.

other than that, just connect both ends

Link to comment
https://www.sau.com.au/forums/topic/377900-help/#findComment-6026661
Share on other sites
SatchiThaStagea Community Regular

SatchiThaStagea

Posted
Posted (edited)

Be sure to put the hose in the right way around or the air will flow backwards. Check for the arrow on the hose.

I think that for those hoses you also need a left-handed screwdriver to tighten the clamps....

Edited by SatchiThaStagea
Link to comment
https://www.sau.com.au/forums/topic/377900-help/#findComment-6029189
Share on other sites
SatchiThaStagea Community Regular

SatchiThaStagea

Posted
Posted (edited)

No that's just for the hoses that run to the flux capacitor, there's no issue if you use a RHS screwdriver provided you stay under 88MPH.

I think your thinking bout the one that runs from the jar of sparks?

I meant the ones that are held up by skyhooks

Edited by SatchiThaStagea
Link to comment
https://www.sau.com.au/forums/topic/377900-help/#findComment-6029729
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...