Jump to content
SAU Community

Recommended Posts

Hi everyone,

QLD VQ-series cruise no.1 is under way for the month of October 2011.

Cruise Information

Date: 15-10-2011 (Saturday)

Time: 3:00pm Meet, 3:30pm Depart - 6pm

Location: Car park in front of Beenleigh Marketplace Shopping Centre (114-118 George Street, Beenleigh QLD 4207)

Please post if interested and check this tread for updates. The cruise will be south bound to Gold Coast as far as Point Danger.

We would like to encourage more VQ-series owners to come along, meet fellow owners and enjoy the sunny cruise.

Looking forward to seeing QLD VQ-series owners.

Thank you.

Link to comment
https://www.sau.com.au/forums/topic/378728-qld-vq-series-cruise-no1/
Share on other sites

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

UPDATED

Confirmed:

1. VNS 24

2. shiva

3. sheldon2369

4. Kolossus

5. Cobey (TBC)

6. T4NK (TBC)

7. V35 350GT

8. Jared (Brisbane V & Z CLUB)

9. Alan (Brisbane V & Z CLUB)

10. Ben (Brisbane V & Z CLUB)

11. Rick Kim

Edited by VNS 24

Hi guys

what time do you think you will be at Point Danger? And that will be AEST I suppose (we're on DST). I was thinking about driving up to say hello & have a look at your cars.

Cheers, Leon.

Hi guys

what time do you think you will be at Point Danger? And that will be AEST I suppose (we're on DST). I was thinking about driving up to say hello & have a look at your cars.

Cheers, Leon.

Hi Leon, pm sent regarding the time and the place.

Please let me know. Thanks.

ALERT!!! ALERT!!!.....Thundery rain forecast on Saturday in Brisbane and Gold Coast areas......:rant:

Yeah, I know. Weather is bad on weekends recently. Hope it's just an early shower.

Edited by VNS 24

UPDATED

Confirmed:

1. VNS 24

2. shiva

3. sheldon2369

4. Kolossus

5. Cobey (TBC)

6. T4NK (TBC)

7. V35 350GT

8. Jared (Brisbane V & Z CLUB)

9. Ben (Brisbane V & Z CLUB)

10. Rick Kim (TBC)

11. Commsman

12. daisu

13. Callan (Brisbane V & Z CLUB)

Hi everyone,

On a side note, there's a shower or two predicted for this Saturday. I can wait til noon to see if this can go ahead.

For those who are keen, please keep an eye out for update on Saturday.

Thank you.

Hi everyone,

Just a reminder about this cruise tomorrow.

Like stated before, this cruise will have to be postpone in afternoon if we have bad weather. Hopefully. it should be fine in evening.

For those who are keen and not on the list, please let me know for map printing, etc.

Thank you.

Edited by VNS 24

WEATHER UPDATE FOR SATURDAY (15-10-2011)

Early thundery rain periods, before afternoon showers and thunderstorms developing.

Looks like it might clear out in evening. I will update again tomorrow morning. Please keep an eye out for weather updates.

Thanks.

Edited by VNS 24

Hi everyone,

Just a reminder about this cruise tomorrow.

Like stated before, this cruise will have to be postpone in afternoon if we have bad weather. Hopefully. it should be fine in evening.

For those who are keen and not on the list, please let me know for map printing, etc.

Thank you.

V35 drivers don't 'cruise' in wet weather??

I drove to Sydney 2 weeks ago (in the rain), went on a cruise with 22 other Stagea owners (in the rain) and drove 8hrs home (you guessed it, in the rain) :happy:.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
×
×
  • Create New...