Jump to content
SAU Community

Recommended Posts

hey guys up for sale is my white 2000 model r34 4 door.

have only owned the car for approximately 8 months but another car has come up for sale i basically have to have so letting this go unfortunately as i cant rep 2 cars.

has been an awesome car since ive owned it however and it will be missed no doubt.

car is turbo and manual! none of this NA auto bollocks

124xxx kms serviced reguarly ( as close to 5000kms as possible)

only a few mild mods, mainly cosmetic.

mods include:

-nistuned computer tuned to 181kw on 8psi (claim by previous owner)

-splitfire coipacks

-origin roof spoiler

-nismo lip kit ( looks the tits, so much more aggressive than stock front bar )

-eyelids

-gunmetal grey rota grid-r's 18x10 +15 rear and 18x9 +20 front. fit wicked, have a perfect amount of poke out the guards, tough fitment

-3 inch dump pipe to 2.5 inch catback (unsure of cat)

-removed spoiler (just taped over holes, was going to weld over and paint etc but selling now so not bothering)

-custom intercooler piping done by AM performance

-pod filter and blocked of BOV for da flutterz

-smoke front and side indicators

-debadged boot

-lowered on some springs of some sort (not entirely sure what they are but theyre a pretty nice ride and high enough to not draw po po attention but low enough to look tough)

-ebc green stuff brake pads done about 5000kms ago up front

-top of the range alpine speakers

-manual boost T (only clicked to stock 8psi except for special occasions)

-aftermarket guage setup (boost, water temp and oil temp which is yet to be installed, as was waiting to be serviced)

thats about it off the top of my head.

asking $16,500 o.n.o i know this might seem steep but regular run of the mill silver na auto 4 doors all sell for 13-14 so a couple extra grand for a white turbo manual one is fair i think

if i get my asking price of 16 i will throw in some SARD 550cc injectors and a highflow r34 neo turbo with op6 housing. setup should be good for 250kw easy with z32 and a better fuel pump

contact on 0430928476 can send pics via mms

post-85706-0-65123700-1318738086_thumb.jpg

post-85706-0-33191400-1318738098_thumb.jpg

post-85706-0-27540800-1318738108_thumb.jpg

located in barossa valley SA, but can travel to adelaide for buyer if theyre serious

Edited by changeofplan
Link to comment
https://www.sau.com.au/forums/topic/380271-r34-4-door/
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...