Jump to content
SAU Community

Recommended Posts

My 1992 R32 GTS-T had an AVO turboworld boost gauge installed in the drivers side vent (to the lower right of the steering wheel) when I bought it.

It has always been a bit useless as it doesn't light up during night driving.

Recently I realised it is much more accurate than the in dash boost gauge and decided I needed to get the backlight wired up (assuming it works) in anticipation of hooking up a turbotech boost controller.

After pulling off the lower drivers side dash panel and pulling the gauge out of the vent a bit I found a red wire and a black wire coming from each side of the gauge housing, the two red wires have been spliced together with another wire attached running to the headlight switch, the two black wires are also spliced together.

After taking off the dash surround with all the switches I could not find any point where the gauge may have been hooked up in the past and the wire connected to the two reds went no where.

Wondering what the easiest way to wire up the backlight to get it to turn on with the headlights, preferentially parkers but otherwise low beam/high beam.

Also has anyone heard of the brand AVO Turboworld before? Is it supposed to be decent?

The boost gauge is mechanical and is joined with a t piece to the stock gauge line.

Edited by Luke HCR32
Link to comment
https://www.sau.com.au/forums/topic/380566-wiring-aftermarket-boost-gauge/
Share on other sites

Will that require me pulling out the head unit or the centre console surround? I have an aftermarket pioneer head unit.

I did notice one of the wires to my fog light switch had a bit of a nick in it (red and green one at top left of plug) could this have been the original source?

You dont need to put a additional fuse in. If youre going to short something and draw so much current, the original fuse for the headlight switch will blow. Sooooo.... theres already a fuse in the circuit. Just splice use the headunit wires.

You can even use the cigarette lighter wires! Shit you could even use youre odometer dash lights as youre source.

Black red. Easy peasy.

Edited by eat_me

make sure whatever you wire it to, it only lights up when the car is on or ACC is on.

some plp make the the mistake and wire it up so its on constantly (common issue with CD players) and they wonder why their batteries keep dying lol

Cheers guys, ended up hooking it up to that frayed fog light switch wire and fixing the wire at the same time, comes on when I turn the headlights to parker or on. Grounded it to the stud above the bonnet release.

post-82729-0-24601100-1319020506_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...