Jump to content
SAU Community

Recommended Posts

1991 R32 GTR

Car is making 270rwkw on 18 psi on a very safe tune.

GT-C Volk 18x9's all round.

Motor rebuilt approx 8000km ago

Freshly serviced and ready for a new owner.

Reco block + head were used.

chemical clean all parts, full machine, clearance and blueprint.

ACL comp bearings

JE Forged piston kit

H-beam rods

MLSR steel head gasket

oil restrictors

Genuine nissan gasket set

all new hoses

new genuine thermostat

new water pump

new timing belt

nismo radiator cap

new battery

new heater core

re gassed air con

nismo diff bushes

cradle spacers (pineapples)

600cc injectors

nismo plugs

Garret 28/60 turbos -7

Apexi power fc with hand controller

full kakimoto 3' exhaust

blitz 4 stage boost controler

R33 GTR crank

N1 oil pump

momo stearing wheel+ gear knob.

Tomei 310km dash cluster

new slotted rotors all round (dba)

koyo rad radiator

baffled sump

bosch fuel pump

central locking + alarm and immobilizer

Good stereo, good tires

Car interior has been retrimmed in leather

car is extremely well looked after washed every week.

always garaged as long as i owned it in TAS

im looking for 24,000 ono

which i think is fair for such an amazing car.

i am also open to swap + cash or straight swap for something of interest.

post-88564-0-36149900-1319090688_thumb.jpg

post-88564-0-07970200-1319090731_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/380720-fs-freshly-rebuilt-r32-gtr/
Share on other sites

http://www.skylinesaustralia.com/forums/topic/370504-1991-r32-gtr-sniper-mint-condition/page__p__5905955__hl__mint__fromsearch__1#entry5905955

Looks like its one of the better ones out there.

Interesting that your advertising it for I assume more than you bough it for.

Good luck with the sale.

I'm selling it due to just moving to Melbourne work is 45 minutes away so I'm looking for something more standard feels like i would be wasting it putting big Kms on such a nice and powerful car when someone can put it to better use.

hmmmmmmm... i went n saw this car just before you bought it. and i know a fair bit about the car... having said that, this car has history being shane's first 32r and is still impressive..

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...