Jump to content
SAU Community

Recommended Posts

Just caught wind of this. Have not heard anything about these failed pumps (which I normally would being an Aussie manufacturer) and if this is so I would be keen to hear about it. Can you enlighten me?

I don't know the exact specifics, however I am pretty sure Forcefed might...

I have heard that there has been at least 2 pumps breaking however I have heard Tomei's have broken aswell since moving their manufacture outside of Japan.

Oh and by the way not made in China!

I should have said outside of Japan instead of just "Made in china"

  • Replies 172
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

All good Kyle. We have only heard of 3 units breaking since we started retailing these many years ago now and we are used to getting feedback when customers have issues.

Out of those 3 units, 2 had broken inner gears due to installation over worn drives (1 of them a factory narrow drive) and the other was not a breakage but the gears had worn the housing and backing plate due to incorrect thrust washer installation on the engine.

The processes involved for gear manufacture from start to finish is an effort believe me and is done to ensure the strongest and most durable possible part is manufactured.It's actually an 8 stage process to do.

All good Kyle. We have only heard of 3 units breaking since we started retailing these many years ago now and we are used to getting feedback when customers have issues.

Out of those 3 units, 2 had broken inner gears due to installation over worn drives (1 of them a factory narrow drive) and the other was not a breakage but the gears had worn the housing and backing plate due to incorrect thrust washer installation on the engine.

The processes involved for gear manufacture from start to finish is an effort believe me and is done to ensure the strongest and most durable possible part is manufactured.It's actually an 8 stage process to do.

Yeah I had heard that there were a couple breaks due to the drive.

At the moment, I am looking at other avenues for an Oil pump mainly because I want the car back on the road and don't want to wait 2 months for Jun to get their stocks up.

I am leaning more towards a HKS oil pump mainly because according to HKS Australia they are the ONLY oil pump that is 100% made in Japan...

At the end of the day, I am sure they are a much of a muchness and It is a matter of just a brand name for the same thing but I am just going by what I have heard and what my builder recommends.... as I don't want to sacrifice a 10thousand dollar engine just for sake of a oil pump gear.

i personally would not use anything but nitto. they easily have the lowest failure rate of any pump, and are local !!! andrew re assembled my pump cos i could not align the backing plate properly. he charged me nothin, not even freight !!! top bloke !!!just remember that mate, japan is a long way away to get help/advice or warranty.

Edited by mico

i personally would not use anything but nitto. they easily have the lowest failure rate of any pump, and are local !!! andrew re assembled my pump cos i could not align the backing plate properly. he charged me nothin, not even freight !!! top bloke !!!just remember that mate, japan is a long way away to get help/advice or warranty.

No offsense but I have yet to hear of a Jun, HKS, Nismo(Not N1) or a Reimax oil pump failing however have heard of 2 Nitto pumps failing... other than the 3 units Andrew specified.

I can understand pumps failing due to poor installation however I am going by what is best for me as running the risk of a oil pump failure on a 10 thousand dollar engine does not make sense to me... something tells me if my oil pump died that it wouldnt be covered under warranty due to a faulty part so not taking the risk with something I have heard has had a failure so often.

Edited by EAT26

Kyle I have failed pumps here from most manufactures and not failures due to installation but failures due to material selection and machining process. I can say that the SCM material used in most supposedly "Japanese" pumps is inferior to the treated EN series steel we use. I could not even count the amount of failed JUN / Greddy pumps (made by the same company which is not either Greddy or JUN) I have seen in my travels on both hands and feet. I also have failed components from most other manufactures also. Honestly most of you guys would not even believe me if I told you what I have seen being manufactured in different parts of the world for different companies.

Now I'm not here for any kind of sales speal because I am a strong believer in options and there is a place in the market for everything from dirt cheap to high end expensive but I am still waiting to hear about these other 2 "documented" failures :whistling: I would normally hear about every issue my customers have and find it hard to believe that if someone had a problem they would'nt contact us being a local company to try and sort something out. Hearsay and facts are 2 different things.

At the end of the day these are mechanical parts we are talking about which all have a limitation but I'm not just guessing that our pumps are stronger than those from the above mentioned brands, I know that they are.

If you are going to judge and make it public then at least back it up guys. And if it is not just hersay then I would prefer to know about it. Feedback is what helps companies that support this industry grow but seems like nobody is interested in that these days.

Kyle I have failed pumps here from most manufactures and not failures due to installation but failures due to material selection and machining process. I can say that the SCM material used in most supposedly "Japanese" pumps is inferior to the treated EN series steel we use. I could not even count the amount of failed JUN / Greddy pumps (made by the same company which is not either Greddy or JUN) I have seen in my travels on both hands and feet. I also have failed components from most other manufactures also. Honestly most of you guys would not even believe me if I told you what I have seen being manufactured in different parts of the world for different companies.

Now I'm not here for any kind of sales speal because I am a strong believer in options and there is a place in the market for everything from dirt cheap to high end expensive but I am still waiting to hear about these other 2 "documented" failures :whistling: I would normally hear about every issue my customers have and find it hard to believe that if someone had a problem they would'nt contact us being a local company to try and sort something out. Hearsay and facts are 2 different things.

At the end of the day these are mechanical parts we are talking about which all have a limitation but I'm not just guessing that our pumps are stronger than those from the above mentioned brands, I know that they are.

If you are going to judge and make it public then at least back it up guys. And if it is not just hersay then I would prefer to know about it. Feedback is what helps companies that support this industry grow but seems like nobody is interested in that these days.

Like I said, I havent heard of the Jun failures however have heard of the Nitto 1s. I am doing what is best for my engine as at the end of the day it is my engine and I have learnt my lesson on taking chances with my car.

I understand you want the feedback however it is not mine to give.

I or Forcefed, where only having an open discussion on oil pump selection in which we have heard and I was told to steer clear from the nitto pump however was told to go a nitto stoker if I could swing the extra costs. He mentioned the 2 documented pumps.... Each pump is different no 2 pumps are the same something like engines you can not garuntee the first pump and the second pump are exactly the same in Tensile Strength nor the other contributing factors... It comes down to personal choice and what you trust.

No offsense but I have yet to hear of a Jun, HKS, Nismo(Not N1) or a Reimax oil pump failing however have heard of 2 Nitto pumps failing... other than the 3 units Andrew specified.

I can understand pumps failing due to poor installation however I am going by what is best for me as running the risk of a oil pump failure on a 10 thousand dollar engine does not make sense to me... something tells me if my oil pump died that it wouldnt be covered under warranty due to a faulty part so not taking the risk with something I have heard has had a failure so often.

my engine had a JUN that had a nice crack through the gears upon inspection, replaced with a nitto item so there is 1 youve heard of.

If you dont feel that nitto is good enough, im not sure what will be

OK no worries but before making claims like "I do know the Tomei, Nitto and Greddy pumps have been breaking so they are not an option" public then at least have the proof to back up. If I hear someone flaming our product then of course I'm going to back it up when to the best of my knowledge the claims are not true. If we didn't go to so much effort and expense with our gearsets on these pumps to be the so durable then this hearsay would not bother me in the slightest.

And yes we can say that one of our pumps is exactally the same as another due to the amount of metalugy testing our gears go through from bar stock to sacrificed finished items. If your interested I'll run you through it as any good manufacturer should be able to.

PS: Here is a picture you might find intersting - This particular vehicle running well over 1000HP and a 2 step had gone through 2x JUN pumps (cracking the inner gear). Now runs a Nitto Pump for last 2.5 years with no such problem.

JUNOPC.docx

Like I said, I havent heard of the Jun failures however have heard of the Nitto 1s. I am doing what is best for my engine as at the end of the day it is my engine and I have learnt my lesson on taking chances with my car.

I understand you want the feedback however it is not mine to give.

I or Forcefed, where only having an open discussion on oil pump selection in which we have heard and I was told to steer clear from the nitto pump however was told to go a nitto stoker if I could swing the extra costs. He mentioned the 2 documented pumps.... Each pump is different no 2 pumps are the same something like engines you can not garuntee the first pump and the second pump are exactly the same in Tensile Strength nor the other contributing factors... It comes down to personal choice and what you trust.

not sure how you could rely on a crank,rod,piston etc. setup but not rely on the pump they produce to feed the engine.

my engine had a JUN that had a nice crack through the gears upon inspection, replaced with a nitto item so there is 1 youve heard of.

If you dont feel that nitto is good enough, im not sure what will be

From my understanding alot of the issue is found either in the oil collar or the housing itself. like the N1s.

In all the cases that I have mentioned not just Jun...

OK no worries but before making claims like "I do know the Tomei, Nitto and Greddy pumps have been breaking so they are not an option" public then at least have the proof to back up. If I hear someone flaming our product then of course I'm going to back it up when to the best of my knowledge the claims are not true. If we didn't go to so much effort and expense with our gearsets on these pumps to be the so durable then this hearsay would not bother me in the slightest.

And yes we can say that one of our pumps is exactally the same as another due to the amount of metalugy testing our gears go through from bar stock to sacrificed finished items. If your interested I'll run you through it as any good manufacturer should be able to.

PS: Here is a picture you might find intersting - This particular vehicle running well over 1000HP and a 2 step had gone through 2x JUN pumps (cracking the inner gear). Now runs a Nitto Pump for last 2.5 years with no such problem.

I would actually like to hear it, as I find it interesting myself.

not sure how you could rely on a crank,rod,piston etc. setup but not rely on the pump they produce to feed the engine.

Your question kinda is self expainatory.

Just because a company and do something right does not mean ALL their products are up to the job.

No worries! Process is as below:


  • Raw material bar stock is purchased from local supplier
  • A cut from both different sizes of bar stock is sent to a metalurgist to check that material composition and supplied hardened state is up to the spec it should be supplied at (a lot gets returned as it is not within specification)
  • After report approval the bar stock is then cut into blanks and rough CNC profiling is carried out
  • These items are then sent for stress relieving
  • The blanks are then properly EDM wire cut into shape
  • They are then sent off for heat treating / nitriding
  • The gears are then specially polished with a particular blend of ceramic media and chemicals to achieve a specified surface finish
  • Several finished gears from each batch are then sent back to the metalurgist to be cut up to measure nitriding depth is within spec as is surface hardness and surface RA

It is from here that we can ok the gears for assembley into pumps and be sure that each ger set is the same as the next and up to our specification.

No worries! Process is as below:


  • Raw material bar stock is purchased from local supplier
  • A cut from both different sizes of bar stock is sent to a metalurgist to check that material composition and supplied hardened state is up to the spec it should be supplied at (a lot gets returned as it is not within specification)
  • After report approval the bar stock is then cut into blanks and rough CNC profiling is carried out
  • These items are then sent for stress relieving
  • The blanks are then properly EDM wire cut into shape
  • They are then sent off for heat treating / nitriding
  • The gears are then specially polished with a particular blend of ceramic media and chemicals to achieve a specified surface finish
  • Several finished gears from each batch are then sent back to the metalurgist to be cut up to measure nitriding depth is within spec as is surface hardness and surface RA

It is from here that we can ok the gears for assembley into pumps and be sure that each ger set is the same as the next and up to our specification.

Cool, very indepth.

Would be cool to see a feature or a video explaining the process.

But at the end of the day. I will hold my tongue on what I am only hearing without proof.

I am looking at the 2.7 stoker for my next build after this 1, most likely wont be in the 33 tho.

At the end of the day, I am just going with what my builder trusts.

Forcefed, might however have some more info behind what he has heard.

Something to look into for the future definitely.

Totally understand going with what your engine builder is recommending.

Good luck with it! I'm sure it will be well enjoyed!

Until I kill it from flogging the life outta it like the last time hahaha.

At least this time I will have the EGT sensors to help push the engine to its limits safetly :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...