Jump to content
SAU Community

Recommended Posts

TEIN suspension for R32 GT-R, great condition, spring seat height adjustable only.

No leaks that I can see, ran great on the car but it's a tad too stiff for daily duties in Sydney (i.e. shithouse roads, I'm too soft).

Turns like a machine.

$700 firm pick up only (no rush to sell these as they are in great condition).

3" cat back exhaust off my GT-R, could possibly fit non GT-R R32s. Has small small 'hotdog' resonator and what looks like an "APC" rear muffler.

Gives your car a great note, selling as I put a quieter system on (I'm getting too old). Has some scratches, it's a 2nd hand exhaust.

$350 pick up only.

Location: Liverpool area, NSW.

Contact: PM is your best bet

I'll get some dodgy pictures later on in the week, busy this weekend.

PM me for my number

$600 for TEINS (I'm getting attached to my current suspension)

$250 for exhaust, it's taking up garage space urrgghh

Also have my R32 GTS-t wreck. No engine/gearbox/front brakes. Diff should be good, power steering was good. Ideal for someone who can drag it onto a trailer/truck. $400 located in St Marys.

2n83346.jpg

vxzrf5.jpg

2h6snk0.jpg

b8p74o.jpg

2wpqrsj.jpg

Lowball away

I also have another set of struts, front Koni dampers rear standard dampers, Eibach springs all round. I thought the Konis were stuffed but it was the upper control arm knocking.

$200

RB20DET silvertop with R34 turbo, loom, ECU $1,500 I think it has around 130,000 km (can't remember the reading on the cluster).

R32 side mount intercooler $40 nothing wrong with it.

Wreck went to waste (was scrapped).

Everything else still for sale.

TEIN suspension - $600

3" cat-back exhaust - $200

Koni front/standard rear dampers with Eibach springs - $200

Standard GT-R cluster - $40

Standard GTS-t cluster - $30

Standard GT-R steering wheel - $20

Nardi steering wheel - $40 (I paid $100 lol)

RB20DET (silvertop) with R34 turbo, computer/loom - $1,500

R32 GTS-t front brakes (4 pots) calipers/pads/rotors - $200

Standard R32 GTS-t side-mount intercooler - $30

No nibbles :(

TEIN suspension - $600

3" cat-back exhaust - $200

Koni front/standard rear dampers with Eibach springs - $200

Standard GT-R cluster - $40

Standard GTS-t cluster - $30

Nardi steering wheel - $30 (I paid $100 lol)

RB20DET (silvertop) with R34 turbo, computer/loom - $1,500

R32 GTS-t front brakes (4 pots) calipers/pads/rotors - $200 or swap for R33 N/A front brakes

Standard R32 GTS-t side-mount intercooler - $20

  • 2 months later...
  • 2 weeks later...

Bump

TEIN suspension - $600

3" cat-back exhaust - $200

Koni front/standard rear dampers with Eibach springs - $200

Standard GT-R cluster - $30

Standard GTS-t cluster - $30

Nardi steering wheel - $30

RB20DET (silvertop) computer/loom *no turbo* - $700

R32 GTS-t front brakes (4 pots) calipers/pads/rotors - $200

Standard R32 GTS-t side-mount intercooler - $20

  • 7 months later...

Yeah mate, still lying around in the shed.

Note RB20DET is gone.

Looking to swap the TEINs back into my car, so Ohlins suspension might be available soon (very good for street).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...