Jump to content
SAU Community

Recommended Posts

Hi,

I need some advice, I had my r32 gtr washed at a Drive in car wash place in Sydney on Sat morning on the way to drop off a radiator at a customers workshop down south. (I work for Fenix Radiators btw), anyway after driving around for a couple of hours and coming home i noticed a massive flake of paint missing off the roof of my car (see pictures attached).

I spoke with my mate who owns/runs MRK Detailing and he said they must have done something that has lifted the paint off the roof either;

buffing it too harshly, using a too ebrasive chemical or hitting it with the gurneys.

I am not sure if there was small crack/chip in the paint before where the flake of paint is missing, but either way what ever they have done while washing it, i believe has caused it to flake off while driving a couple hours after.

I have spoken to the company involved on the day it happened, then took it back to them on the sunday and then spoke to the "head office" today, and they all have tried to blame a few different things for it happening, saying it must be old shitty paint, or the was a rust bubble there ect. He was trying to say that they have no liability if that is the case. I thought they would have a duty of care to either notify me that there was a problem with the paint work or for them not to hit the area with the gurney or while polishing it. He also said that gurneys would not pull the paint off the car unless there was a problem with the paint in the first place. I have heard plenty of stories about gurneys getting to close and ripping up the paint.

So at the moment he said he will check with the manager that i spoke to and showed the car to on sunday tomorrow and would get back to me.

I know i might be a bit silly in going to one of these places in the first place. But i was desperate and needed to clean the car before going and dropping off a rad to a customer.

So in the mean time does any one have any advice on how to approach the situation or if i am likely to be compensated for what has happened???

I have kept a log with everything that had gone on and will keep one going for as long as i need to.

Cheers in advance guys for your thoughts! :thumbsup:

post-65119-0-33008000-1320642729_thumb.jpgpost-65119-0-20473200-1320642992_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/382300-help/
Share on other sites

Too be honest i couldn't see much around, but i didn't really have a great look. But for that reason that i couldn't easily notice a t & c board and that i wasn't made aware of one that even if they did have one i could get around it? Sort of like those stupid national car parks thing. Because for awhile they weren't made properly visable and accesible to every one??

Link to comment
https://www.sau.com.au/forums/topic/382300-help/#findComment-6099260
Share on other sites

did you recieve a receipt with any t&c on it?

and i dont think there is much you can do if there is one but it wasn't brought to your attention.

also id go back to the car wash and just look around for a t&c sign or something allong those lines or get a mate to go there and get him to ask them what happens if any damage is done to there car

Link to comment
https://www.sau.com.au/forums/topic/382300-help/#findComment-6099284
Share on other sites

Yea i deffinately will be going back there. I have been looking up on the fair trading website. I found some interesting stuff with on this page:

http://www.fairtrading.nsw.gov.au/Consumers/Consumer_guarantees_warranties_and_refunds/Guarantees_on_services.html

"Due care and skill Due care and skill means they must:

  • use an acceptable level of skill or technical knowledge when providing the services, and
  • take all necessary care to avoid loss or damage when providing the services.

For example, a consumer hires a painter to paint her house. Before starting the job, the painter does not remove all of the old, flaking paint. Six months later, the new paint starts to flake. The painter has not met the due care and skill guarantee, as he did not use a level of skill that would be expected of a reasonable painter.

While painting the consumer’s house, the painter knocks over a can of paint, which spills over her newly paved driveway. The painter has not met the guarantee, as he has not taken the care expected of a reasonable painter. "

So i guess i could fight that even if they did have t&c that if they have done something while "detailing" :wacko: my car which has caused it to flake like that then really their t&c should be irrelevant! Or maybe i'm just talking outta ma asss... Plus i might go and do some filming one day, as when i was there on sunday i was watching a guy with the gurney standing with gun going full tilt onto a customers car while chatting to another employee. Too me that isn't fulfilling his responsibility to uphold the aspect of "due care"??

Link to comment
https://www.sau.com.au/forums/topic/382300-help/#findComment-6099381
Share on other sites

DFT will do nothing about it and car wash won't have any liability to it, especially as there is no other damage caused by them such as a dent or other sections of the paint flaking off due to misstreatment or harsh chemicals.

Looking around the pic with the 50cent coin in it, it is clear the paint is not in good condition, not to mention the car is over 20 years old now. Having only noticed the issue after leaving the premesis will only make your case even harder to prove.

Might as well send DFT a letter or call them up as it wont cost you anything other than your time. But don't be surprised if you get nothing out of it.

You mention buffing, harsh chemicals or gunnery. I would guess that it wasn't buffed as it is a run of the mill carwash place (unless you opted for it?), it definately isn't hard chemicals as it is only localised to a small section of the car and you would not be the only one with the issue being vocal about it. My money would be on a high pressure cleaner that unluckily got under some previous damage, most likely from a stone chip, as the paint is old and the bond between it and the metal has been damaged by Australias heat and sun rays, this is more than likely the case.

There is nothing wrong with high pressure cleaning, but it just shouldn't be done on older cars original paint with damage on it.

Link to comment
https://www.sau.com.au/forums/topic/382300-help/#findComment-6099597
Share on other sites

DFT will do nothing about it and car wash won't have any liability to it, especially as there is no other damage caused by them such as a dent or other sections of the paint flaking off due to misstreatment or harsh chemicals.

Looking around the pic with the 50cent coin in it, it is clear the paint is not in good condition, not to mention the car is over 20 years old now. Having only noticed the issue after leaving the premesis will only make your case even harder to prove.

Might as well send DFT a letter or call them up as it wont cost you anything other than your time. But don't be surprised if you get nothing out of it.

You mention buffing, harsh chemicals or gunnery. I would guess that it wasn't buffed as it is a run of the mill carwash place (unless you opted for it?), it definately isn't hard chemicals as it is only localised to a small section of the car and you would not be the only one with the issue being vocal about it. My money would be on a high pressure cleaner that unluckily got under some previous damage, most likely from a stone chip, as the paint is old and the bond between it and the metal has been damaged by Australias heat and sun rays, this is more than likely the case.

There is nothing wrong with high pressure cleaning, but it just shouldn't be done on older cars original paint with damage on it.

Yea i get what you mean. But i might as well try. I mean essentially they should take me over the car or something and explain to me any issues that could arise. Would only take 30 seconds from when i get out of the car. But yea it won't hurt to give it a shot.

Link to comment
https://www.sau.com.au/forums/topic/382300-help/#findComment-6099810
Share on other sites

seen the same thing before and sorry for ya champ but nothing u can do and is not realy the car wash's fault by the looks of it the top layer of paint was pealled off by what id say a high presure watter jet, this would have gotten under the paint work at that little rust spot you can see down the bottom end,

is actualy verry common to see a stone chip that cracks the paint and watter gets under the layer, even if u would have washed it yourself with the high presure hose the same thing would have happened and you wouldnt have seen it till it was to late.

Link to comment
https://www.sau.com.au/forums/topic/382300-help/#findComment-6099930
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I did end up getting it sorted, as GTSBoy said, there was a corroded connection and wire that needed to be replaced. I ended up taking out the light assembly, giving everything a good clean and re-soldered the old joints, and it came out good.
    • Wow, thanks for your help guys 🙏. I really appreciate it. Thanks @Rezz, if i fail finding any new or used, full or partial set of original Stage carpets i will come back to you for sure 😉 Explenation is right there, i just missed it 🤦‍♂️. Thanks for pointing out. @soviet_merlin in the meantime, I received a reply from nengun, and i quote: "Thanks for your message and interest in Nengun. KG4900 is for the full set of floor mats, while KG4911 is only the Driver's Floor Mat. FR, RH means Front Right Hand Side. All the Full Set options are now discontinued. However, the Driver's Floor Mat options are still available according to the latest information available to us. We do not know what the differences would be, but if you only want the one mat, we can certainly see what we can find out for you". Interesting. It seems they still have some "new old stock" that Duncan mentioned 🤔. I wonder if they can provide any photos......And i also just realized that amayama have G4900 sets. I'm tempted too. 
    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
×
×
  • Create New...