Jump to content
SAU Community

Recommended Posts

hey, i'm currently installing a fusion alarm into my R33 and trying to connect it into my factory keyless central locking but in doing this I must of shorted something and the central locking no longer locks or unlocks from the switch, door or remote...

Just wondering if anyone here is able to tell me things to try to get the central locking working again I have checked all fuses, the smart entrance module and the factory keyless module both click when I try to unlock or lock but nothing else happens.

take it to a pro, did you buy that alarm off e-blow, I saw one from Fusion for sale ?

really you could have fried everything from a wire to a curcuit board and if your 33 has a airbag your lucky it didnt hit you in the face from point blank.

ALARMS are best left to a pro for best results..... to many things can go wrong with DIY .even with instructions and wiring guides you have to know what your doing and how to hide it

did you loose anything else , radio, cig light, dome light etc? are you sure you checked everything ??? are you getting any clicking on the relay for the factory locks ?

might be time for aftermarket lock actuators ???

take it to a pro, did you buy that alarm off e-blow, I saw one from Fusion for sale ?

really you could have fried everything from a wire to a curcuit board and if your 33 has a airbag your lucky it didnt hit you in the face from point blank.

ALARMS are best left to a pro for best results..... to many things can go wrong with DIY .even with instructions and wiring guides you have to know what your doing and how to hide it

did you loose anything else , radio, cig light, dome light etc? are you sure you checked everything ??? are you getting any clicking on the relay for the factory locks ?

might be time for aftermarket lock actuators ???

bought it from a car audio shop in Christchurch, New Zealand. Have also done plenty of wiring in cars before, tested with a multimeter to find lock and unlock wires, central locking is the only thing not working and yes there is clicking on the relay for the factory locks. If I can't find where the problem is I will be installing aftermarket lock actuators.

Apart from this problem everything else on the alarm is functioning correctly.

dealer fitted keyless entry in the drivers door?

if so then there are lock unlock wires on the SE unit. I will let you find them but I will say they are there.

dealer fitted keyless entry in the drivers door?

if so then there are lock unlock wires on the SE unit. I will let you find them but I will say they are there.

yes it is dealer fitted keyless entry.

I already know the lock and unlock wires on the SE unit from the multimeter test, for some reason the central locking all stopped working after tapping into these wires... At this stage i'm seriously thinking about installing an aftermarket central locking system to interface with the alarm (done this on last car that had a completely different central locking problem).

ok factory central locking is working again and alarm also unlocking and locking doors :) pulled the smart entrance module apart and found i'd burnt a hole in the circuit board lol that's why you double check the polarity of the locking systems first... just soldered a bridge across it to fix it.

Just one other thing now, the drivers door doesn't lock or unlock like it used to with the central locking so guess I blew the motor in that door will have to look to see if it's cheaper to replace the motor or get a 2-wire actuator for that door.

no it will be a separate feed. if this is a S3 then the actuator will be in another module. if its S2 then there will be a unit in the door. actuator will be fine as it takes a hell of a lot to kill one.

no it will be a separate feed. if this is a S3 then the actuator will be in another module. if its S2 then there will be a unit in the door. actuator will be fine as it takes a hell of a lot to kill one.

ok thanks, i'll take the door panel off and have a look to see if there's a unit there

IF there is a module in the drivers door it will be INDEPENDENT of the SE unit. you will need to bringhte actuator wiring OUT of the door and REMOVE the extra unit AND modify the harness to suit.

if this sounds too hard - stop.

IF there is a module in the drivers door it will be INDEPENDENT of the SE unit. you will need to bringhte actuator wiring OUT of the door and REMOVE the extra unit AND modify the harness to suit.

if this sounds too hard - stop.

will be doing this soon ;) can't learn things if you don't do them yourself... also do you know a way of disabling the automatic locking over 25km/hr without also disabling the defroster?

Ok did you have remote entry before you started this?

yes remote entry is the dealer fitted one and the drivers door definitely has the factory actuator installed (4-wires go to it, i tested these with a multimeter while locking and unlocking other doors, one has constant 10V on it, the rest showed nothing)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...