Jump to content
SAU Community

Recommended Posts

All for sale as I have bought a Haltek and Racepack dash, some of these were in my shed and taking up space as well

First off we have a Defi Link set:

80 mm boost(new) $200

80 mm tacho(used) $200

60 mm oil pressure(used)$250

60 mm oil temp(used)$200

60 mm water temp(used)$200

Defi Link thing number 2(used)$100

Warning meter (new) $50

IMG_0790.jpg

Oil temp and pressure come with mount so you can just bolt it on (fits gtr and rb30)

Water temp comes with a mount to plug straight into a gtr

All sensors and an extra 2m link wire included as well

Condition is all good

Obviously I want to keep it all together and sell as a job lot as that easier so if you want the whole lot pm me and we can work out a deal, otherwise i shall separate them

Next up is a Greddy meter set, all used, off my old Zed

They are all silver in colour

60 mm oil pressure $150

60 mm boost pressure $150

60 mm water temp $150

60 mm oil temp $150

IMG_0787.jpg

IMG_0788.jpg

All sensors and wires included

Once again cheaper if you buy the lot

Next one is a Greddy kit in white, all used

60 mm exhaust temp with new sensor $200 (sensor cost more than that alone)

60 mm boost temp used $150

IMG_0786.jpg

Apexi boost gauge, heckit

60mm 30 bux(currently starts at 0,5bar)

IMG_0785.jpg

But wait there is more(how awesome in 5 years of hoarding!

80 mm pivot boost gauge $50

IMG_0789.jpg

and now for the steak knives...

I have 5 x 60 mm Jetspeed EGT sensors(new)

$50 each.. these things are awesome!

IMG_0784.jpg

and an old school Apexi air flow controller $40

IMG_0791.jpg

All located Lower Blue Mountains, Sydney NSW

Pick up or postage at buyer's expense

Pete

0448468884

Link to comment
https://www.sau.com.au/forums/topic/382898-guages-defi-greedy-pivot-ect/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Keen on the 80mm boost gauge and link. How much shipped to SA 5114?

And just incase I change my mind, how much for the full Greddy set shipped?

Keen on the 80mm boost gauge and link. How much shipped to SA 5114?

And just incase I change my mind, how much for the full Greddy set shipped?

Looking to keep the defi set complete, but I can do $520 posted for the silver faced Greddy set of four gauges

:)

Call it $500 flat and you got a deal... I've been on the 31 club too long, keeping the lowball alive and well. Ha.

Shoot me payment details and I'll swing some cash your way.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes the gear for the R33/34 is different, it is red and has a different number of teeth. My part didn't come with that gear though, so I don't know how many teeth are on the red one. You'd have to reuse the 260RS/R33 gear, as long as it's not destroyed.   Haha, as unfortunate as that might be it was working fine for about the first 1500km I've had the car for now.
    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
×
×
  • Create New...