Jump to content
SAU Community

Recommended Posts

Hey everyone,

Have a heap of standard R32 GTR parts for sale...

Standard R32 Gtr turbos, both in great condition with no play, wheels in good condition only need a clean - $600

Standard turbo manifolds for rb26 - $150

Standard dumps rb26 - $75

Aircon setup for r32 gtr including compressor, radiator and hoses up to the firewall - $300

Standard Rb26 timing cover in blue - $50

standard R32 GTR camshafts with gears - $100

R32 GTR rear wing - $200

Universal carbon wing at the moment the stands have spacers on each side to fit in the rear stock mount of the r32 gtr however front holes need to be drilled, had it on my r32 gtr before going a different direction is height adjustable i think 25cm and 40cm and is approx 155cm long, and about 26cm wide - $500 in great condition and has heavy duty feet for stands.

R32 GTR V-spec alloy front guards, the paint is not great on the left guard, looks like it was pressure packed... right one is not too bad will sell as a pair or separate - $300

Standard r32 GTR brakes, front and rear, calipers are electric blue, rotors have a heap of meat left on them - $550

I can ship anything at the byers expense, and open to offers on everything.

Contact me via PM or on 0434817247 and ill try to get back to you asap. All parts are located in Wollongong, about 1hr south of Sydney.

Link to comment
https://www.sau.com.au/forums/topic/383483-r32-gtr-parts/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...