Jump to content
SAU Community

Recommended Posts

I have a problem with my BNR34 UK-Model with Link Ecu

I have no 4wd and A-LSD and the fail code 72 (TPS)

After I bought a new TPS I wanted to calibrate it and now the problem.

I can only calibrate it like in the BCNR33 manual (0,4 and 3,8 Volts on Pin38) but the BNR34 manual says I should calibrate to 0,5 and 4,2 Volts. But this isn`t possible at max I get 3,9 Volts or so and this dont fit at idle....

next problem, my mfd showes around 50% at full throttle. So I checked pin 56 and there I have 0,25 Volts at idle and 2,1 Volts at full throttle. but this should have 0,5 and 4,2 Volts or not?!

What is going wrong there?! =(

__________________

Good build thread man. 1 thing I didn't quite understand is why didn't you go for a reasonably sized single turbo setup instead? I had my last R34 GTR with -5's and now the R32 with -5's, both are laggy as f**k. And went in my friends R32 gtr with a single T04Z setup and 2.8L engine, the thing has lot more response! You did a full hearted engine rebuild so wouldn't it be better if you ditched the twin for a decent sized single turbo setup? That way you would have got more top end power with better response and less turbo lag. Just my personal opinion... :)

Edited by G0Z1LLAAAAA34
  • 2 weeks later...
  • 2 weeks later...
  • 1 month later...

After problems with my Link ECU and the AWD System I got my revised ECU back. Its all fine now =)

Throttle: ECUPin 38 and 56 = 0.5Volt

2012-12-17200853_zps46424085.jpg

Vollgas: Pin 38 und 56 = 4.1Volt

2012-12-17200858_zps58649a4f.jpg

No 4WD & A-LSD light, all fine =)

I bought some speedo LEDs , but I need better ones =(

2012-12-17211943_zps3979f187.jpg

But red light is looking really better I would say =)

  • 2 weeks later...

Big boys can also have small toys^^

1st my AutoArt 1:18 BNR34 R-Tune in red

DSCF1867_zpsdc76050a.jpg

DSCF1864_zpsc40655f6.jpg

DSCF1835_zps3ea60fcc.jpg

DSCF1808_zps590556db.jpg

DSCF1802_zps0c756fc1.jpg

DSCF1791_zpsc1a8b3c4.jpg

DSCF1775_zps0d7e2f9f.jpg

DSCF1759_zpsbace871e.jpg

2nd my HPI 1:43 BNR34 Z-Tune in limited red/black edition

DSCF1873_zps095946f7.jpg

2012-12-29000037_zps2bc680cd.jpg

2012-12-28235012_zps3e61d075.jpg

2012-12-28235727_zps95749dd5.jpg

2012-12-28235519_zpsaae8fde9.jpg

2012-12-28235106_zpsd49fe8a4.jpg

2012-12-28234706_zps2a75dddf.jpg

2012-12-28234654_zps68842126.jpg

So, finally I hope you had merry christmas and wish you a happy new year 2013

541854_531001506910680_117850124_n_zpsd84d98f6.jpg

Happy new year guys!

Here are my first news for 2013

This is engine bay before

2012-12-31161031_zps4e1bc6fe.jpg

and here the engine bay now, with my GReddy Suction Kit, but without my apexi filters because I need other adaptors

2013-01-02172553_zpsa72715dd.jpg

2013-01-02172658_zps46c38e57.jpg

2013-01-02172719_zps58b4d695.jpg

2013-01-02172806_zps2b808e6e.jpg

2013-01-02172741_zps57d3c25b.jpg

And also my toy collection is complete now =)

DSCF1886_zps6919be1e.jpg

My Sky is getting famous^^

The story: We have done a photo shootig in year 2010 with a model. Now, two years later this model campaigns in the television show "The Bachelor"

This is the reason why she is in the bestselling newspaper called "BILD" now, with my car.

Here are the pics

200550_520587394640338_1641908703_n_zpse2ed7255.jpg

735724_542307115793627_2016722554_o_zpsdf2a955f.jpg

IMG-20130105-WA0001_zps4a799731.jpg

579062_108551409282140_582011931_n_zpsf4864756.jpg

543687_108510762619538_1519754484_n_zpsaf3549f1.jpg

393068_397148773702181_283234455_n_zpsb7ff7f7a.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...