Jump to content
SAU Community

Recommended Posts

I have got some of these parts listed on this forum but it is getting a bit confusing what is left for sale so here they are.

GTR R34 Left/Right Xenon headlights perfect condition. $1000 plus postage

GTR R34 V Spec Front disc rotors (no Calipers) and complete set of rear rotors(322mm N1) with Brembo calipers all the brake lines. $1600 the lot plus postage.

Genuine HKS purple dual feed fuel rail with fittings to suit 11mm injectors for RB26 perfect cond. $200 plus postage

Siemens 900 cc injectors for RB26 will bolts straight onto standard fuel rail and use the standard connectors (with flow chart of you want it) perfect condition less than 3000 klms old. $400 plus postage.

STD GTR R34 harmonic balancer perfect cond. $130

GTR R34 Rear Tail shaft perfect condition. $400 plus postage

GTR R33 front tail shaft good condition. $150

Call Dave

0412 950192

Xenon headlights for GTR R34 still here, they are in perfect condition with not a scratch , lens are crystal clear

( did have someone buying them but usual story no money)

Cheap at $1000 will incl freight.

text me on 0412 950192

Cheers Dave.

Xmas Bump

I have got a Blitz NUR spec stainless exhaust good condition for a GTR R34.... $450 plus freight.

6 x 800cc seimens injectors, done 1000 klms, perfect condition will supply flow chart..... $400

Edited by SkylineSky

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...