Jump to content
SAU Community

Recommended Posts

Hi.

I recently had a wheel allignment done by a reputable specialist and they noted that lots of my alignments were way out of the acceptable limits. I have gathered a few parts to help correct these issues but am having trouble finding any information on how to adjust the rear toe?

So what I'm after is a product that will allow more adjustment. I was looking for Toe Rods but apparently they don't fit 32 GTR's.

Any help would be appreciated.

And just incase it helps I currently have Tein Coilovers and whiteline swaybars both front and rear and a hicas lock bar I also have rear traction rods and rear upper camber arms on the way. As well as Front upper camber arm and Castor rods.

Link to comment
https://www.sau.com.au/forums/topic/384059-r32-gtr-toe/
Share on other sites

OK the good news is what you need is very simple. not toe rods but tie rods ;)

Assuming nothing is bent....

The rear toe on a GTR is controlled by a steering rack, exactly like the front every other car. The steering rack is called HICAS.

At the end of the steering rack there are a few pieces that require replacement over the years. From outside (hub) to inside (steering/hicas rack) they are:

Ball joint - there is a nasty little ball joint pressed into the hub. I have only ever found these at nissan. They are expensive if they need replacement, but if they are rooted it makes a hge difference to fix them

Rod End / Outer tie rod - this is the most common wear point in most cars, and suspension places that don't know gtrs often suggest they be replaced when there is movement. There are reasonably priced (ie not nissan) options to replace these. They are normally OK on GTRs because the inner tie rod end wears first....

Inner tie rod - this is the most common wear point on a gtr. There is a non-nissan option (sorry I don't have the brand or part number handy). There is a nylon bush on the end of the inner tie rod end that wears causing slop or movement in the racks/hubs. These often need replacement.

But....you said you needed to adjust the rear toe. Like most car's front steering rack, there is normally heaps of adjustment available in the factory setup. If they can't fix it with the factory gear you almost certainly have something else bent.....so the easiest fix is to replce the bent bit, then everything else will come good, the way nissan designed it. There are some cases where the factory toe genuinely runs out of adjustment, but this is normally only the case with extreme lowering or race car style alignment

Link to comment
https://www.sau.com.au/forums/topic/384059-r32-gtr-toe/#findComment-6126892
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...