Jump to content
SAU Community

Recommended Posts

Just clearing out some stuff that is no longer needed.. I am open to offers.

All parts located in Penrith, Western Sydney.. Will post but note clutch is heavy and will cost approx $50 to post

R34 GTT brake master cylinder + booster.. Bought it because I thought my booster was farked but all was well so just onselling it.. $120+postage

IMAG0189.jpg

IMAG0190.jpg

Q45 AFM (90MM) I bought this with the intention of using on my car but looking at going MAF-less ECU so its no longer needed.

As you can see in the pics the mesh is pefect and the body has no cracks or scratches. Comes with a used plug $100+ Postage

IMAG0180.jpg

IMAG0181.jpg

IMAG0179.jpg

R33 Gts-t/R34 N/A heavy Duty Clutch + OEM Flywheel.. Started slipping at high RPM and was replaced with a Hyper Single

Clutch disc needs replacing ($150 from kudos motorsports+shipping) all surfaces are still perfectly flat and smooth. Includes flywheel and pressure plate.. Looking for $100

IMAG0192.jpg

IMAG0193.jpg

IMAG0191.jpg

send me a txt on 0412589924 or pm me here.

Thanks,

David

bump.. booster $100

Clutch $20

also have my old r34 GTT Impul Front bar that was used as a drift bar, its fiberglass.. has some small cracks and will need a repair/spray if you want to use it everyday.

has been cut to fit FMIC $50

  • 2 weeks later...

ask and ye shall recieve..

mainly scraped on the bottom of the bar from hitting on a driveway.. minor cracks/chips on the face but would be fixed if you decided to repaint it

post-51757-0-04935100-1324692926_thumb.jpg

post-51757-0-54710300-1324692941_thumb.jpg

post-51757-0-47013600-1324692956_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...