Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Looks a little high, but that is not how Nissan gauges work. Basically all Nissan temp gauges will warm up to their normal running temperature, and sit there until the fluid actually boils (and you have broken something), and only THEN goes off the richter scale hot. Generally they don't move much inbetween.

But you should put a real temp gauge on every Nissan car imho - espeically one with a 95-100 degree warning light. Boiling cars is the 2nd easiest way to blow an engine (next to not enough oil/low oil pressure).

I put an awesome EL overlay over my cluster, and in the process of fitting it put my temp gauge out of scale - mine now sits between the 3rd and 2nd last lines when at operating temp (and already 1/3 way up when cold at start up). That's why I put in a real temp gauge

bleed the system, might need topping up. at that needle position youre probably looking at around 110-112degrees water temp. not the best, but is still operational.

if it doesnt have air in the system, look for a blockage, or check the status of your thermo fans. does it go back down when youre cruising again? if it doesnt, possibly a water pump issue.

Gosh...I and my mech didnt pickup this overheat issue when we do inspection before buying. Now it becomes annoying....

Do you guys think i should go back to Nissan dealer to have diagnosis checks? Or anyone can recommend any reliable mech in Brissy?

Thanks for you guys help~

or just check the fluid level so that you dont pay someone $180 to top up the radiator......

Did check fluid level is full & top water hose is not too hard to press, fan is only running when a/c is on but even a/c on, the temp is keeping in above middle line...what eles i should check by myself?

Your thermo fan should come on even when the a/c is off, once the car gets hot enough.

I would be checking for air in your system (which I bet is the cause). Or get a mechanic to install a water temp probe and actually check your water temp to see if your stock gauge is lying/broken.

bleed the system, might need topping up. at that needle position youre probably looking at around 110-112degrees water temp. not the best, but is still operational.

if it doesnt have air in the system, look for a blockage, or check the status of your thermo fans. does it go back down when youre cruising again? if it doesnt, possibly a water pump issue.

Just found your question when i was a bit panic, sorry, mate~

I havent flush the coolant yet, but will do soon.

What do you mean by "doesnt have air in the system, look for a blockage" how to check it? I check my fan only runs when a/c on but it doesnt go back to normal temp even with fan (a/c on) on or when i am cruising again.

Water pump issue? What other procedure that i can check whether it is water pum failure? Pls advise, thanks~

Your thermo fan should come on even when the a/c is off, once the car gets hot enough.

I would be checking for air in your system (which I bet is the cause). Or get a mechanic to install a water temp probe and actually check your water temp to see if your stock gauge is lying/broken.

Thanks, Andrew. How can you check air in your system?

Unscrew the little plastic bleed screw in the left hand side at the rear o fthe engine. If you look along the water piping you will see it - it is black plastic and has an X in it to unscrew it with a phillips-head screwdriver.

Hi Mikhail, so have you ever checked by Nissan or any V35 SERVICE SPECIALISTS before? Or you just leave it as it is?

I am leaving mine as is as I am pretty certain its normal. I think I saw a similar thread on here that said the same thing. I had mine serviced and no problems were found. Also my needle is just below the middle, yours is above middle.

If you have access to someone with a datascan tool, get them to check the coolant temperature with it, if it is around 85-90 deg C, then I wouldn't worry about it. Especiallly if it doesn't seem to go up and down when driving hard, or climbing hills

If you have access to someone with a datascan tool, get them to check the coolant temperature with it, if it is around 85-90 deg C, then I wouldn't worry about it. Especiallly if it doesn't seem to go up and down when driving hard, or climbing hills

I wrote a proper bleed procedure somewhere on G35, just search my name.

Also get a radiator cap with temp control gauge on it, you can go check yourself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...