Jump to content
SAU Community

Recommended Posts

Chris would proberbly know. From what I've seen playing with mine is they are powered so I jumper or something is needed on the non option deck to power it. Also haven't seen back of a non Bose radio so don't know if they got the space for the plug.

also, no, there is no wiring to the sub for the non-bose cars. but there is an amp built into the sub enclosure, so it wouldnt be difficult to work out the power wires and the audio input

no mate i dont, im lacking the mounting screw for the sub to hold it and the spare wheel into the wheel well.

if i did, id have it hooked up already! i THINK it uses a speaker level input from the amps that are usually in the boot of the bose equipped models.

from an aftermarket head unit, i wouldnt imagine it would be too hard to wire up.

for $80 its worth taking the risk! lol

  • 2 weeks later...

as a FYI. these need at least a 6Vpp balanced signal into them to run properly.

if its still available can you take a measurement from the base to the top of it. I want to see if I can get it in the spare tyre well of my R32.

Hi there, I am in Adelaide & also interested. I have sent you a PM.

you would be better off with the 6x9s that go in the rear shelf of yours..

you would be better off with the 6x9s that go in the rear shelf of yours..

Would you have any recommendations? While you are at it what about the fronts also? I know that it is subject to personal taste & budget but maybe a rough guide would interest a few people.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...