Jump to content
SAU Community

Recommended Posts

Anything sent international should be sent with tracking numbers, I haven't sent anything overseas but everything I have had sent came with them. Mostly car parts too, so as a business they should be sending it traceable as well. Its not like it's costing them money, you would take that extra cost. And if you're like me, I'd believe you wouldn't mind paying an extra $30-50 or whatever for knowing just where a couple of grand worth of parts are

Link to comment
https://www.sau.com.au/forums/topic/384787-xspeed/page/2/#findComment-6141709
Share on other sites

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

$120/hr is the going rate nowdays, there are a few stealerships down here charging $140/hr. I charge not even half that and apparently i'm still expensive

im $149.50 p/h. want me to clean your pool Corey?

ive never had much success with xspeed over the phone. jamie was pretty good though. but when i go in there i get someone to have a chat with. bit hard when im down here though.

not sure who i will use yet once the car is back together :rolleyes:

Link to comment
https://www.sau.com.au/forums/topic/384787-xspeed/page/2/#findComment-6141745
Share on other sites

Get the same shit also :(

Best part is when they purchase product online and try install them self but fail , come in and get ass raping

f**kin hate that. Guy purchased a clutch off ebay cos he didnt want me to supply one, it didnt fit so the car tied up the hoist for 4days waiting for a return from Victoria. He couldnt see why i charged him the 4 days for the car sitting there

Link to comment
https://www.sau.com.au/forums/topic/384787-xspeed/page/2/#findComment-6141791
Share on other sites

f**kin hate that. Guy purchased a clutch off ebay cos he didnt want me to supply one, it didnt fit so the car tied up the hoist for 4days waiting for a return from Victoria. He couldnt see why i charged him the 4 days for the car sitting there

I think you hit the nail on the head with that one. :thumbsup: So many people can't understand the costs incurred by a business through having it using up equipment that could have been used on other jobs.

Link to comment
https://www.sau.com.au/forums/topic/384787-xspeed/page/2/#findComment-6142289
Share on other sites

Well we charge $132/hr ($120+ GST). Compared to the "stealerships" we are quite reasonably priced considering the types of cars we work on; places like the Audi Centre, Westpoint Star and Lexus of Perth all charge close to $200/hr from what I understand.

I charge $132 per.hour at my 'Stealership' as you all lovingly call it lol

Paul, when was the service you paid 500? Not since I was there I'd hope?

Link to comment
https://www.sau.com.au/forums/topic/384787-xspeed/page/2/#findComment-6142314
Share on other sites

f**kin hate that. Guy purchased a clutch off ebay cos he didnt want me to supply one, it didnt fit so the car tied up the hoist for 4days waiting for a return from Victoria. He couldnt see why i charged him the 4 days for the car sitting there

The old 'customer supplied' product eh :)

Link to comment
https://www.sau.com.au/forums/topic/384787-xspeed/page/2/#findComment-6142321
Share on other sites

I think you hit the nail on the head with that one. :thumbsup: So many people can't understand the costs incurred by a business through having it using up equipment that could have been used on other jobs.

Especially in a 1 man operation where i depend on the hoist on my days off. Cost me a few cancelled jobs that i may or may not get back

Link to comment
https://www.sau.com.au/forums/topic/384787-xspeed/page/2/#findComment-6142393
Share on other sites

. He couldnt see why i charged him the 4 days for the car sitting there

I charge $250 a day for it sitting on hoist ,Only had to charge twice .

1st time was auto one supplying owner with wrong clutch for a terrano ( 3days ) and 2nd was owner purchased camry clutch from coventrys ( 1 day ) Best part was on both jobs we were alot cheaper on the part so that makes me smile even more :)

Link to comment
https://www.sau.com.au/forums/topic/384787-xspeed/page/2/#findComment-6142416
Share on other sites

I charge $250 a day for it sitting on hoist ,Only had to charge twice .

1st time was auto one supplying owner with wrong clutch for a terrano ( 3days ) and 2nd was owner purchased camry clutch from coventrys ( 1 day ) Best part was on both jobs we were alot cheaper on the part so that makes me smile even more :)

So if it stays on the hoist a week do I own the hoist ? :whistling:

Link to comment
https://www.sau.com.au/forums/topic/384787-xspeed/page/2/#findComment-6142418
Share on other sites

But I'm guessing he didn't see it that way ?

They never do

I charge $250 a day for it sitting on hoist ,Only had to charge twice .

1st time was auto one supplying owner with wrong clutch for a terrano ( 3days ) and 2nd was owner purchased camry clutch from coventrys ( 1 day ) Best part was on both jobs we were alot cheaper on the part so that makes me smile even more :)

I am gona have to put my prices up. You usually are cheaper with the clutches, if only you'd return my calls lol :nyaanyaa:

Link to comment
https://www.sau.com.au/forums/topic/384787-xspeed/page/2/#findComment-6142429
Share on other sites

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...