Jump to content
SAU Community

Recommended Posts

Hey =)

I keep hearing people say get your car tuned to unlock its potential, but I'm unsure of what's involved in a tune up, as opposed to a service.

What is actually involved in tuning up a non turbo R34? Is it worth doing on a non turbo? I think it might involve ECU mods and tightening bolts maybe?

I'm also looking for a good place to get the tune up done, My family has been to ultra tune. To avoid the defamation rules, I won't say anything, but I do not wish to go there.

Any help and advice would be appreciated.

Link to comment
https://www.sau.com.au/forums/topic/387020-r34-tune-up/
Share on other sites

Generally it does mean the ECU side of things. When designing/producing a car, there are certain standards/restrictions that need to be adheard to. This could be carbon emissions, reliability requirements or even fuel consumption.

When a car is tuned, the tuner alters the settings to specifically cater for the exact car and circumstances by changing things like fuel maps ect to gain the power that was de-tuned out of the engine oringally for the reasons above mentioned.

You can't go to any garage to have your ECU tuned. It would have to be a place with a dyno and specialist knowledge/equipment.

It is not cheap and the gains to be had by tuning what I'd assume is a largely stock N/A skyline are definitely not worth it.

Link to comment
https://www.sau.com.au/forums/topic/387020-r34-tune-up/#findComment-6171930
Share on other sites

What about a stock turbo 34?? Would it be worth it then? Also do they jst tune ur ecu or u need a new one/computer??

Also my 34 has been converted to manual since owning it, would a tune be also beneficial do to it being tuned for an auto ?? Sorry for the dumb questions but gotta learn some how

If it's stock it will be roughly the same as mad said, maybe a little more.

It's when you start upgrading things like your cooling or fuel systems you can start playing around, as you can run things more towards their capacity.

If your car is completely stock, for the price of a nistune ($1000) you'd be best getting a FMIC and a boost controller and putting the boost up to 12psi. You will see a larger increase from stock then a tune alone.

Link to comment
https://www.sau.com.au/forums/topic/387020-r34-tune-up/#findComment-6173092
Share on other sites

What about a stock turbo 34?? Would it be worth it then? Also do they jst tune ur ecu or u need a new one/computer??

up to maybe 20kw on a r34 gt-t from a good tune if you are running a front mount, full exhaust and higher boost. if the car is dead stock then the gains would be much less. as was said, you will get more gains from doing those mods than just the tune. and on a r34 gt-t you can have a nistune installed in the stock ecu.

Also my 34 has been converted to manual since owning it, would a tune be also beneficial do to it being tuned for an auto ?? Sorry for the dumb questions but gotta learn some how

if it is still running the auto ecu then probably. it partly depends on how they did the wiring when they did the gearbox conversion. the autos are designed to only be able to be started in neutral or park. i'm pretty sure they send a signal to the ecu, which controls this. most people who put manual boxes in just trick the ecu into thinking it is in neutral or park all the time, so the car will start whenever needed. the downside to this is that the ecu has different mapping for park/neutral to when it's in gear. manual gearboxes have a switch in them which also tells the ecu when it's in gear so that it changes the mapping, but unlike the autos you can still start the car with it in gear.

long story short, if it's still running the auto ecu then i'd start by looking at getting a manual ecu for it and making sure that the gearbox switch is working properly. (a consult cable and progrum such as datascan can tell you this)

Link to comment
https://www.sau.com.au/forums/topic/387020-r34-tune-up/#findComment-6173837
Share on other sites

  • 3 weeks later...

up to maybe 20kw on a r34 gt-t from a good tune if you are running a front mount, full exhaust and higher boost. if the car is dead stock then the gains would be much less. as was said, you will get more gains from doing those mods than just the tune. and on a r34 gt-t you can have a nistune installed in the stock ecu.

if it is still running the auto ecu then probably. it partly depends on how they did the wiring when they did the gearbox conversion. the autos are designed to only be able to be started in neutral or park. i'm pretty sure they send a signal to the ecu, which controls this. most people who put manual boxes in just trick the ecu into thinking it is in neutral or park all the time, so the car will start whenever needed. the downside to this is that the ecu has different mapping for park/neutral to when it's in gear. manual gearboxes have a switch in them which also tells the ecu when it's in gear so that it changes the mapping, but unlike the autos you can still start the car with it in gear.

long story short, if it's still running the auto ecu then i'd start by looking at getting a manual ecu for it and making sure that the gearbox switch is working properly. (a consult cable and progrum such as datascan can tell you this)

Hi Mad,

So if i had mine converted to manual (R34Gtt, FMIC, aftermarket Radiator, Turbo Back exhuast) can i just plug and play the manual ECU? Or there is wirings I need to swap around or cut or rewire??

If need to cut and rewire or whatever do you know which wires are they on the harness or pin number to which?? Cos I'm experiencing Rev cut around 6k or 6.5k mark. Is this to do ith the ECU??

Thanks

Daniel

Link to comment
https://www.sau.com.au/forums/topic/387020-r34-tune-up/#findComment-6201087
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which is why I didn't mention that hardness testing, and specifically mentioned the bore and deck thickness testing. Yeah, not really. The bore temperature will be a lot more even around the top half inch or so, where the material distribution is dominated by the deck, and which is the only place where the bore surface temperature heating any gas in the cylinder is likely to have any effect on detonation. Think about it. Another inch or so down the bore, you might have a hotter spot. The gas there might get a bit hotter, then the piston rises squeezes that gas away from there at high speed and mixes it with other gas from nearby. Instant dilution of the problem. I'd be surprised if it was an issue at any time other than in racing engines or OEM dev engines being run at the ragged edge of tuning. Say what now?
    • https://dsportmag.com/the-tech/education/engine-tech-material-hardness-testing/ The PRP testing on block hardness I'm not sure how much it actually can be trusted. The thinner cylinder walls on RBs is a bit of a problem vs 2JZ but it really depends on the design goal. Siamesed cylinder bores like a 2JZ cause uneven cylinder wall temps too, which means a bit of distortion induced by that + the hotspot can affect knock margin. Something that actually gives me a bit of pause with the PRP block, whether super thick cylinder walls are going to keep it from being drop-in compatible on an otherwise OEM rebuild. 
    • Yeah very valid point. I am waiting for one of the other tuners to come back from vacation so he can help me a bit when the cat is installed again. In the meantime I am going to finish up my polishing and ceramic coating that I have started myself.    N45 Dr Beasley product is highly recommended for a paint primer / polisher. Using this EXO Gtechniq also for the ceramic but next time might use the light serum before hand also. Looks great. 
    • Running rich in conditions where it shouldn't probably won't do great things for catalytic converter lifespan. I would fix that sooner than later.
    • Yes, important point. Watch the Motive videos with Herman thickness testing the bores and deck. You do not want to push the unlucky (thin) block as hard as you can push the average block.
×
×
  • Create New...