Jump to content
SAU Community

Recommended Posts

i recently got into a car accident and was uninsured at the time. The guy i hit said he went to a few smash repairs and said the quote to fix the damage was roughly 5.5k, i am no panel beater but i think is overpriced. i have uploaded pictures of the damage but the pictures arnt that good of a quality because they were taken on my phone,to sum it off the extend of the damage looks to be the rear bumper and the reinforcment bar was scraped but not pushed in. Can someone tell me if i am being roughted

thanks for the help

post-87166-0-13911500-1325963655_thumb.jpg

post-87166-0-56112500-1325963691_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/387511-urgent-need-advice/
Share on other sites

If its just a rear bumper bar, then to the extent of the damage described, their ripping you off. whole resprays can be done for 10 grand.

To get it done should be a lot cheaper, (around the thousandish dollar mark)

go get some quotes from some quality workshops, and see what they give u as an estimate, as shopping around is your best option. (if you bring all of the replacement parts/source them yourself, they may even drop the price further)

also if push comes to shove, look for another bumper at a wreckers, this could save you a few $$$ plus bumpers are not overly hard to change over.

Just my 2c of what i know from the industry, hope it helps

:cheers: Aaron.

I would say it may be slightly on higher side but then again I haven't see the car in person and aren't in the industry. I got a light tap in the rear of my R33 GTST and it ended up being approx $3.5K. It pushed in the rear metal plate in the boot and some other things causing it to not line up. The Friday arvo that it happened I almost thought it would buff out however once I started to have a look with the panel beater the damage started to show. The V35's might be stronger in the rear than the R33?

It looks to be a fibreglass rear bar as plastic ones don't tear like that. So, you have to replace the rear bar to start with which may need to come form overseas? The reo bar needs to be fixed if damage or possibly replaced. It may have pushed some of the structure that it bolts to. The panel shop then needs to make the bar fit the car properly as a lot of the time they won't line up with the car. That can take time which equals cost. To paint a rear bar I'd expect $400-500.

Just remember that you cannot always see the damage until some trim is taken off and you can get a good look at things.

I'm not just directing this at you but anyone who reads this.. For the sake of everyone on the road (you included) please get some insurance!!!! I would be so fn angry if I was the one you hit. Imagine if you hit something like a BMW 5 series you could be in a world of hurt, more to the point the poor owner of it would.

I would say it may be slightly on higher side but then again I haven't see the car in person and aren't in the industry. I got a light tap in the rear of my R33 GTST and it ended up being approx $3.5K. It pushed in the rear metal plate in the boot and some other things causing it to not line up. The Friday arvo that it happened I almost thought it would buff out however once I started to have a look with the panel beater the damage started to show. The V35's might be stronger in the rear than the R33?

It looks to be a fibreglass rear bar as plastic ones don't tear like that. So, you have to replace the rear bar to start with which may need to come form overseas? The reo bar needs to be fixed if damage or possibly replaced. It may have pushed some of the structure that it bolts to. The panel shop then needs to make the bar fit the car properly as a lot of the time they won't line up with the car. That can take time which equals cost. To paint a rear bar I'd expect $400-500.

Just remember that you cannot always see the damage until some trim is taken off and you can get a good look at things.

I'm not just directing this at you but anyone who reads this.. For the sake of everyone on the road (you included) please get some insurance!!!! I would be so fn angry if I was the one you hit. Imagine if you hit something like a BMW 5 series you could be in a world of hurt, more to the point the poor owner of it would.

only if they didn't have insurance, which is highly unlikely

as for the damage, it looks like there could be close to that sort of amount of damage. as people have said, it isn't just the bar, but the reo bar, that black grill thing in the bar probably has broken clips and i wouldn't be suprised if the exhaust is bent too. there is also the chance that the reversing sensor wiring is damaged.

Well what happened was he told me the day after the accident it would cost roughly there i asked what they were fixing all he told me was rear reo, rear bar, clips and for them to rematch the colour. Fair enough i told him to go thru insurance as it was to much for me to pay in a lump sum, about a week later he told me he had no insurance so i needed to pay cash so i found it abit sus because on the day of the accident he asked if i wanted to fix it privately or handle it with his insurance

Before handing over any money, arrange for the car to be taken to a pannel beater of your choice as well.

3k for a rear bar seems steep, but then again, I have gotten prices from Nissan Australia before and they weren't cheap

35's are getting to be nearly 10 years old, there should be a few rear bars going at wreckers by now.

Edited by PWND

Its an aftermarket bar so will nissan still know the price?

In that case no. You would have to find out what brand it is and get a price

3k seems like a bit of money for a rear bar. Might include the price of a rear reo as well, but still seems a lot.

As I said, arrange for him to take the car to a pannel beater of your choice and get a quote

Remove/Refit:

R/bar = $55

splash shields = $25

T/lamps = $20

boot trims = $45

r/bar reinforcement = $25

Total:$170

Repairs:

Beaver/Rh Drop panel = $180

Reinforcement = $120

Total:$300

Paint:

R/bar = $180

Reinforcement = $90

Beaver/Rh drop panel = $110

mix/match = $25

Oven Allowance = $75

Total:$480

So labour all up your looking at about $950 mark plus whatever parts you may need....IMO i think you're getting ripped

I'm a motor assessor and these are the figures i'd allow from quotes (this is just going by what i can see in the pics)

Hope that helps :D

Remove/Refit:

R/bar = $55

splash shields = $25

T/lamps = $20

boot trims = $45

r/bar reinforcement = $25

Total:$170

Repairs:

Beaver/Rh Drop panel = $180

Reinforcement = $120

Total:$300

Paint:

R/bar = $180

Reinforcement = $90

Beaver/Rh drop panel = $110

mix/match = $25

Oven Allowance = $75

Total:$480

So labour all up your looking at about $950 mark plus whatever parts you may need....IMO i think you're getting ripped

I'm a motor assessor and these are the figures i'd allow from quotes (this is just going by what i can see in the pics)

Hope that helps :D

Tis good to have you along... :thumbsup:

sorry to bump this up, but do not under any circumstance just go off his quote. he could have just gone to a friend and had him quote you a fairytale.

if you are paying out of your own pocket, if he wants to see the money, you both have to agree on a repairer.

otherwise, let him take you to court. ensure you communicate to him in writing that you would like the car inspected at an agreed smash repairer, and you should have no issues.

The court is not going to award the one quote he got from a smash repairer he selected himself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...