Jump to content
SAU Community

Recommended Posts

Wheels factory R33 GTR forged 17*9 with 255 width tyres near new $1500

post-33414-0-00042600-1325984928_thumb.jpgpost-33414-0-42607400-1325984923_thumb.jpg

Power FC for R32/R33 GTR, includes hand controller original packaging and manuals $800

post-33414-0-20889400-1325984862_thumb.jpgpost-33414-0-69559800-1325984865_thumb.jpg

Factory RB26 Airflow meters 3 good ones and 1 intermitantly faulty one available $80 each

post-33414-0-84749300-1325984651_thumb.jpgpost-33414-0-53695200-1325984670_thumb.jpg

Factory Air Box R33 GTR, Factory Snorkle R33 GTR, K&N Filter for standard airbox

post-33414-0-53842700-1325984656_thumb.jpg post-33414-0-58820500-1325984665_thumb.jpgpost-33414-0-32384600-1325984663_thumb.jpg

Rear Brake pads R33 GTR, Factory brake lines, Factory cam gears

post-33414-0-88019200-1325984672_thumb.jpgpost-33414-0-67398900-1325984674_thumb.jpg

Factory Coil Packs, assume working else previous owner would not kept them

post-33414-0-52375800-1325984680_thumb.jpgpost-33414-0-67859000-1325984676_thumb.jpg

Dumps & Turbo's, 1 turbo blown, sitable for rebuilding

post-33414-0-43417600-1325984731_thumb.jpgpost-33414-0-53666700-1325984874_thumb.jpgpost-33414-0-24593500-1325984871_thumb.jpg

R33 GTR Vspec 4WD computer, had intermitant issues but were not fixed by replacement, so assume it it OK, at your own risk.

post-33414-0-70739500-1325984852_thumb.jpg

Factory Intercooler piping

post-33414-0-14796200-1325984856_thumb.jpg

Sparkplugs unknown quality

post-33414-0-69557700-1325984858_thumb.jpg

Near new sparkplug, platium. Used for less than 100km but replaced by copper by tuner due to some technical issue with the car since fixed.

post-33414-0-08326800-1325984868_thumb.jpg

Factory Fuel pressue reg???

post-33414-0-18263300-1325984849_thumb.jpg

Factory Washer bottle

post-33414-0-77403100-1325984876_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/387528-gtr-parts-inc-wheels/
Share on other sites

Updated, had to leave before completing all prices. Discounts possible if you want multiple items.

Airbox $150, Snorkle $60, Filter, $40 or ($200 for all)

Brake pads (rear) $10, brake lines $10

Cam gears $20ea

Coil Pack $50

Dumps and Turbo's $50

4WD computer $40

Intercooler piping $10

sparkplugs $5

Near new platium spark plugs $10 ea or $50 for all

Fuel pressure reg??? $5

Washer bottle $20

Shipping extra, just tell me what type, insurred registered etc

Lots of stuff gone. Here's an updated list of available parts.

AFM's $80 each

Brake pads (rear) $10, brake lines $10 (For this price have them as spares, oem approved etc)

6 Coil Packs $50

4WD computer $40

Intercooler piping $10

sparkplugs $5

Near new platium spark plugs $10 ea or $50 for all

Washer bottle $20

(take the lot, make a stupid offer, I can only say no)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...