Jump to content
SAU Community

Recommended Posts

Hey,

Do you have the metal screwn and black body plug for the motorised aerial? I don't need an aerial, just the external attachments as per picture below.

  • 2 weeks later...
  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

Hey,

Do you have the metal screwn and black body plug for the motorised aerial? I don't need an aerial, just the external attachments as per picture below.

Hey mate do have a set somewhere but I'll have to have a look and see if I can find them.

Anyone wanting paarts is best off contacting me via PM rather than posting in this thread.

NOW ACCEPTNG ANY AND ALL OFFERS ON WHATEVER I STILL HAVE

5 Stud hubs & sumitomos

3" straight through mild steel exhaust with Xforce 5" cannon

various suspension bits and pieces.

rear subframe

repairable write off shell with compliance plates & sunroof

dash

heaps of other random bits and pieces.

\Also for sale in coming weeks will be a series 2 RB25DE, 207,xxx km's, serviced every 10k since I've owned it, runs well. Will come with S2 loom and S1 electrics.

More parts to add.

17x8 +35 17x9+38 Advan SA3R. Polished lip, silver centres. 9" centres have been painted grey. All come with complete centrecaps. lips are in pretty poor shape. lots of rash etc. Decent set of Kuhmo KU21's included(235/45 & 245/45) Would make good skid rims/spare rims.

$350 ono

17x8 +35 17x9+38 Enkei RS Evolution 3 piece. Polished lip, silver centres, paint is in average condition, all centrecaps included. One lip has a big bit of rash the rest have minor rash. bald pirellis on the rears, can't remember what's on the fronts. 1 8 doesn't have a tyre attached as it tore itself apart.

$450 ono

RB25 NEO coilpacks, set of 6, unbranded. unsure of K's, seemed to be working well on my S2 RB25DE?

$100 ono

R34 S2 GTT Front seats, drivers side outer bolster has been repaired at some point otherwise in really good shape. rails included.

$200 ono

KR4 Sonic Silver R33 front guards, passenger side has a slight tear along lower bodyline, and paint is wrecked from previously mentioned tyre :/ Drivers side is perfect. whole front end was resprayed ~6 months ago

$200 ono for both or $100 for passenger, $150 for drivers side.

Pics to follow

hey mate have u got the power steering rack? or inner tie rod ends? 0434283410

Hey mate yes I have a P/S rack. No leaks, no bends moves smoothly. Inner tie rod ends, rack ends? I can include them but one is bent and the ball joints in both are pretty knackered. You can get a new pair for $50 though.

Can do the rack for $100ono. PM me if you're keen.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...