Jump to content
SAU Community

Recommended Posts

  • Replies 102
  • Created
  • Last Reply

Top Posters In This Topic

Wow, you're car looks great, almost exactly the same as mine only mine doesn't have all the badging and stuff on it (to be thruthful im glad, didn't want some dick trying to get the S logo off the bonnet with a screwdriver :bonk: )

As for my baby :) booked in for rego on Thursday, should pick it up next weekend if all goes well. I'm all psyched up now! :)

Anyways, good luck with it, that's one nice looking car!

lol we will probably be on the road at the same time maybe you a couple of weeks earlier :) yea the badge on the bonnet will come off ASAP looks a bit homo on that note any tips people that have removed it is it glued on or does it have some sort of bolt/attachement.

yea i would see if i do want it in the end but i was thinking POSSIBLY i dont know how it would look yet but see if it would mount between the bonnet and the bart like were people ahve their GT-R one i could just put that S... not sure if it would look dicky or not but we will see hopefully it looks good

  • 3 weeks later...

well the car arrived today took it for a quick spin around the block mmm turbo's are nice. other than that it needs a really good clean and a bit of cut and polish and it will be sweet as. Goes into rego on thursday and seeing as how it is stock as a rock it should have no problems. also tested all power options eg indicators, break lights, mirrors windows etc etc all work fine so yea i may actually get spotted soon WOOT. hope to catch up with some of you soon.. FINALLY :wassup:

Nice work mate! Took delivery of mine yesterday too. Went for a spin around Manuka...i wasn't driving cause i don't get to till november but it's still a great car to be a pasenger in. Picked up rego for mine as well, the last 3 digits are 33M :)

yeah, lets see, i got the custom plates sheet here (i wanted GAJ 33T but it cost about $1,800!!!!) the example RH 351 costs $313 for tin and $399 for plastic, unique plates (like GAJ 33T) are $1,894... if it looks like a manufacturer or model (e.g Ni55an) that's $3,531 and numeric plates go from $627 to $4,602

Almost forgot, plates with your name on them with seven or less characters cost $627.

I just ended up getting standard plates, but the lady at the motor registery Gaye was really nice and after seeing the number combo i wanted went and found plates with the numbers 33 in them. 33M or 33C... i went for M.

About the plates, i noticed the standards fit just fine in the rear bracket, but at the front they're a few centimetres too long and had to be bent to fit in the mounting brackets. It looks pretty crappy. Is it possible to get a smaller plate for the front and how much would i be looking at for that? I want to keep it blue + white like the standard plate on the back too.

About the plates, i noticed the standards fit just fine in the rear bracket, but at the front they're a few centimetres too long and had to be bent to fit in the mounting brackets. It looks pretty crappy. Is it possible to get a smaller plate for the front and how much would i be looking at for that? I want to keep it blue + white like the standard plate on the back too.

on the R32 the plates dont fit at all without bending, so the front i moved to the side and the rears bent, not much can be done about it

good to see the two of you will both be on the road soon,

Kinda yes....but what would they prefer? no plates at all? :D

When i get around to ordering a plastic replacement for my tin ones, i'll whip up a bracket to side mount it. Give more flow to what's left of my intercooler, and looks good too :) Brake ducting...who needs brake ducting...i've got a great big stainless pipe there for the intercooler anyway

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...